What is Depth of etrailer Idler Hub # AKIHUB-545-2-G-1K

Question

Question:

what is the depth of the hub? My current hub is 4 deep.

asked by: Chuck J

0

Expert Reply:

Hey Chuck, the Trailer Idler Hub Assembly for 2,000-lb Axles # AKIHUB-545-2-G-1K that you referenced is 4 inches deep just like the hub you have now. This is the standard depth for hubs that fit this axle capacity.

expert reply by: Jameson C

0

Jameson C.

12/1/2025

Hey Chuck, did the 4-inch deep hub end up matching your setup the way you expected? Knowing how it fit could help others looking to replace a similar hub.

Answer 1

Based on your photo it looks like you have 2,700 lb axles, and we do have hubs for that size axle. However, you will need to confirm the bearings your current hub has. You will need to take apart your current hub assembly and look at the bearings…

view full answer...

Answer 2

If you blow out a grease seal on a trailer hub by overfilling it with grease using a Bearing Buddy the seal would not still be okay as it would need to be replaced but the Bearing Buddy like the #BB1980A-SS would still be fine. It's very easy to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

What is Depth of etrailer Idler Hub # AKIHUB-545-2-G-1K

Product Page this Question was Asked From

Continue Researching