How Much Tongue Weight Can Weigh Safe Adjustable Pintle And Ball Drop Hitch Handle?

Question

Question:

How much tongue weight does the WS64WR handle before it maxes out?

asked by: Sam

0

Expert Reply:

Hey there Sam. The Weigh Safe 8" adjustable drop hitch # WS64WR is rated for a 2,200-lb max tongue weight on the 3 inch shank. That’s a lot of capacity for big equipment trailers, lowboys, and loaded dump trailers. It comes with an easy-swap 2" ball, 2-5/16" ball, and pintle hitch attachment.

What kind of trailers are you pulling most often at that weight?

expert reply by: Andrew N

0

Answer 1

Hi Jim; for your 2025 Ford F-350 I recommend the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BW73FR. The Turnoverball allows you to store the hitch ball upside down when not in use for full bed access. It also uses a square base so it…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 12

There sure is K.C.. For a shorter weight distribution shank that fits a 2-1/2" hitch, I recommend the Equal-i-zer item #EQ90-02-4700. This shank measures 12" long x 9-1/2" tall. It provides up to a 3" drop and has a 16,000 lbs…

view full answer...

How Much Tongue Weight Can Weigh Safe Adjustable Pintle And Ball Drop Hitch Handle?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching