Can I Purchase the 3M Button Clips for WeatherTech Floor Mats Separately?

Question

Question:

Can I purchase the 3m button clips for the weathertech floor Mats separately?

asked by: Rusty E

0

Expert Reply:

I am sorry Rusty but we do not sell the 3M button clips separately for the WeatherTech Front Auto Floor Mat item # WT4410631 you were looking at. I recommend reaching out to WeatherTech directly as my only solution would be to sell you new floor mats.

expert reply by: Jerred H

0

3M Button Clips
(click to enlarge)

Answer 1

Hey Donnie! The only thing we would have is the Tuson Heavy Duty Truck Module Kit for DirecLink Brake Controller item #335HDCON-9PIN, which it sounds like you already have. This one is specifically designed for the Volvo semi's. It works with the…

view full answer...

Answer 2

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 3

The wiring color codes and wire gauge recommendations for the Pollak Heavy-Duty, 7-Pole, Round Pin, Trailer Wiring Connector, item #PK11700, are listed below. White - Ground Return - 8 gauge Black - Clearance, Side Marker, Identification - 12 gauge…

view full answer...

Answer 4

On a 7 pin round which is the common connection on a semi trailer, the clearance/marker lights are at the 10 o clock position when you look at the trailer wiring connection. When looking at the connector on the back of the truck, that will put the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Can I Purchase the 3M Button Clips for WeatherTech Floor Mats Separately?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching