Horse Trailer Door Latche Kit That Stays Tight And Doesn't Rattle

Question

Question:

My stock latch rattles loose on gravel roads. Will this M3 latch hold tighter? going on a horse trailer tandem axle

asked by: Kayla

0

Expert Reply:

Kayla, that’s exactly where these cam-action latches shine. The cam pulls the rods into the keepers with tension, which keeps the door tight against the frame and cuts down on rattling. It’s a big upgrade over some of the factory straight-bar setups.

We have the 36" latch # M393FR, the 45" latch # M343FR, and the 55" latch # M363FR.

Do you mostly run short local gravel hauls, or longer trips where the vibration really wears on things?

And for everyone else, what’s been your trick for keeping trailer doors rattle-free?

expert reply by: Andrew N

0

Answer 1

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 2

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 5

Hi Jeremy! You can definitely adapt your 16K PullRite SuperGlide 5th Wheel Hitch for Short Bed Trucks #PUL93RR to fit your new 2025 Ford F-350. What you will need is actually what you asked this question from, the Adapter Rails for PullRite…

view full answer...

Answer 6

Hey Jeff. The Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs item #AL83DQ, you were looking at, are compatible with the B&W item #BW73FR, however they are only for the dually models of the 2025 Ford F-350. For the non-dually F-350…

view full answer...

Answer 7

Hey Jeff! I'm not sure who told you that but the information is incorrect. The MORryde X-Factor Crossmember can be used with the AllTrek 4000 like #MR29DR. The correct X-Factor crossmember is the #MR33WR which is the same as the XF12-001. You can…

view full answer...

Answer 8

Hey Eddy, so the DeeMax aux fuel tank part #DZ91752X is a gravity feed design and does not use any pumps. So what does that mean as far as over filling? If the fill line has a check valve built into it then you are okay to leave it open as that would…

view full answer...

Answer 9

Hello Jeff, thanks for reaching out. MORryde actually makes an X-Factor crossmember specifically for use with the CRE3000 equalizers. For that you will need the following: - MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR For full…

view full answer...

Answer 10

Kayla, that’s exactly where these cam-action latches shine. The cam pulls the rods into the keepers with tension, which keeps the door tight against the frame and cuts down on rattling. It’s a big upgrade over some of the factory straight-bar setups.…

view full answer...

Answer 11

Hello Jeff, Sounds like you’ve got a big camper (about 4,000 lbs) on your 2024 F-350 dually, and when it’s loaded, the truck feels bouncy and sways a bit. That’s pretty common with heavy campers, especially if the suspension is still stock.…

view full answer...

Horse Trailer Door Latche Kit That Stays Tight And Doesn't Rattle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching