Replacement Sensor for TST Tire Pressure Monitor System

Question

Question:

Need repeater for 8 sensor TST-507-RV-8-C. Replacement for my system

asked by: Don W

0

Expert Reply:

Hey Don, thanks for reaching out!

The replacement sensor for your TST TPMS for Trailers and Cars # TST35FR (TST-507-RV-8-C) is the part # TST-507-R on our site.

What happened to the old sensor?

expert reply by: Jon G

0

Replacement TST Sensor
(click to enlarge)

Jon G.

9/2/2025

Hey Don, did the new signal booster work well with your system? I'm asking because your experience could help others in a similar situation.

Answer 1

Hey Jesse, since you have a Dexter 12k axle you would need the Kodiak disc brake kit part #KD87FR for the brake components and then for an idler hub you'd need the part #8-214-8UC1 which the disc brake kit would slip over. Are there hydraulic…

view full answer...

Answer 2

When removing the rotor on your 12k Dexter disc brakes, all you need to do is pull it off of the hub assuming you have already removed the caliper. The only thing that secures it to the studs is the wheel and lug nuts when you put the wheel on. It is…

view full answer...

Answer 3

Hi Robert; do you have a TST system like the #TST-507-RV-4-C? How old are the sensors? The #TST-507-RV-S4 sensors have a battery life of 12-18 months so it sounds like it might be time to replace the sensor if it is no longer detected. They are also…

view full answer...

Answer 4

The operating frequency of the Signal Booster / Repeater for TST TPMS #TST-507-R is 433.92 MHz.

view full answer...

Answer 5

The Signal Booster / Repeater for TST TPMS part #TST-507-R is designed for TST tire pressure monitoring systems like part #TST-507-RV-4-C. The repeaters/extenders aren't universal as they don't all use the same frequency. We don't offer…

view full answer...

Answer 6

As you have the Monitor #TST-507-D-C you will simply need the Signal Booster #TST-507-R to go along with some new tire sensors. You do have the option of what sensors you will prefer to use from the list below. Brass Tire Sensors for TST TPMS - Qty 2…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Sensor for TST Tire Pressure Monitor System

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching