How to Install the Replacement Spring on a Fulton T160 Hand Winch

Question

Question:

I purchased a spring for a Fulton T160 winch. I need a diagram to figure out how to install the spring. Thanks

asked by: Randal B

0

Expert Reply:

I have attached the instructions sheet for the Fulton hand winches that shows how to replace the ratchet spring. I have also attached a link to one of our other expert questions that includes a video showing how to disassemble and reassemble the ratchet pawl and spring.

Basically, you will need to remove the bolt holding the ratchet pawl in place. Be sure to note how it came apart because there will be about 7 pieces total. On the spring, there is a narrow end and a wide end. The wide end hooks into the ratchet pawl and the narrow end hooks to the winch frame.

expert reply by: John H

0

click to enlarge

Answer 1

The Replacement Spring #4769-28 that you referenced will install onto the pawl assembly of your winch. Check out the pictures I attached that show an exploded diagram to see how it installs.

view full answer...

Answer 2

I checked with my contact at Fulton who confirms that the #4769-28 replacement spring is indeed a fit for your Fulton T1802 hand winch. I've provided an exploded drawing showing how the spring sits on the winch.

view full answer...

Answer 3

Hey Earl, The #F86ZR is designed for 2-speed Fulton winches so you would need the 7302027 or 4769-28 single speed spring for your Fulton Single Speed Winch #FT16020301. It looks like we not longer offer this spring so you'll want to reach out to…

view full answer...

Answer 4

The Replacement Spring #4769-28 that you referenced will install onto the pawl assembly of your winch. Check out the pictures I attached that show an exploded diagram to see how it installs.

view full answer...

Answer 5

I spoke to my contact at Fulton and he said the correct replacement spring for the ratchet of your Fulton F2 winch is the part #4769-28. I attached a picture that shows a diagram for the winch for you to check out. You will be able to see how the…

view full answer...

Answer 6

I attached a video to the right that shows a coworker of mine who made a video of how to replace the spring in your Fulton T2000 winch. This will walk you through the process.

view full answer...

Answer 7

I have a few options for you to help with replacing the hubs on your trailer. The first and easiest method would be to crawl under the trailer and look for the axle tag on the beam. This should give an axle capacity which we can then use to find the…

view full answer...

Answer 8

From past experiences with your trailer we do know a bit about what hubs are typically going to fit but I would recommend you verify first by checking your trailer. We have found that your trailer has inner bearing L68149, ID 1.378, race OD 20362,…

view full answer...

Answer 9

The Replacement Spring for Fulton Winch #4769-28 that fits your Fulton winch T3205 is a torsion spring. The price of the spring is noted on the product page.

view full answer...

Answer 10

The Fulton F2 Fully Enclosed Trailer Winch with Strap and Adjustable Handle - 1,600 lbs #FW16000101 will not need to be completely taken apart to replace the spring, but the housing, the pin and ratchet pawl will need to be removed to replace the…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

How to Install the Replacement Spring on a Fulton T160 Hand Winch

Featured Help Information

Miscellaneous Media

Continue Researching