What Is Max Weight Rating For Bulldog Winch 17-Piece Deluxe Ratcheting Vehicle Tie-Down Strap Set?

Question

Question:

Is the 3335 pound rating for the entire vehicle or per strap. In other words what weight vehicle will this kit secure?

asked by: Frank W

0

Expert Reply:

Hello Frank, thanks for reaching out. For the Bulldog Winch 17-Piece Deluxe Ratcheting Vehicle Tie-Down Strap Set # BDW20351, the 3,335 lb rating is per strap. It comes with four straps so the max vehicle weight for this kit would be like 13,000 lbs.

What kind of vehicle were you thinking of using them for?

expert reply by: Jesse M

0

Bulldog Winch 17-Piece Deluxe Ratcheting Vehicle Tie-Down Strap Set
(click to enlarge)

Jesse M.

8/7/2025

Hey Frank, how did the Bulldog Winch Tie-Down Strap Set work out for your vehicle? I'm curious to know if it was the right fit for securing your ride, as it might help others in a similar situation.

Answer 1

While there aren't any ratchet straps that fit directly in stake pockets of a trailer, we do have stake pocket tie-down anchors that you can use as a way to connect the ratchet straps; what you can use is the Stake Pocket Tie-Down Anchors…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...