Replacement Head Covers for Lippert Solera 2000 Awning

Question

Question:

can you provide the correct front cover for this awning? I may also need the back cover as it looks like one of the tabs have been broken, but not sure how these install.

asked by: Trevor G

0

Solera 2000
(click to enlarge)

Expert Reply:

Hi Trevor; what happened to your awning? You can use the Lippert Edge covers to replace the one on your Solera 2000 awning. It does look like you broke off a tab so you will need the # LC32NJ for the front cover and # LC43UD for the back.

expert reply by: Robin H

0

Trevor G.

7/7/2025

great question and I have no Idea ! thanks for the info

Robin H.

7/8/2025

@TrevorG I understand, I have also been a victim of mystery damage. Happy to help!

Answer 1

I forwarded your photo to my Lippert representative, and found that the correct front drive head cover you'd need is Lippert part number 771407 which we carry as part #LC32NJ. Thanks for providing the photo, that make the process much easier!

view full answer...

Answer 2

You are going to need the Solera Awning Plain Drive Head Front Cover #LC289557 and Back Cover #LC289558 for your awning. Due to your covers being the oldest style that Lippert made they are no longer available and this is the updated cover. If you…

view full answer...

Answer 3

Hello Ron, thanks for reaching out. We do offer the Lippert Edge Drive Head Cover in white. Take a look at the following: - Replacement Front Cover for Lippert Edge RV Awnings - Drive Head - White #LC42BX

view full answer...

Answer 4

Hello Gary, thanks for providing all of the info and part numbers for your awning. That does come back as one of the Lippert 2000 series awnings. It sounds like you might be looking for the Replacement Pitch Arm Assembly #LC93BX which is for the 2000…

view full answer...

Answer 5

Meg, for your Lippert Solera 2000 series awning you can use the Replacement Front Cover for Lippert Edge Awnings #LC32NJ for the front and #LC43UD for the rear to replace your damaged cover. Also, if by cap you're meaning the manual override…

view full answer...

Answer 6

We do offer replacement covers for the heads of the Lippert Edge awnings. For the drive head, you'd want the #LC32NJ cover you'd looked at and for the idler head, use part #LC37UD.

view full answer...

Answer 7

Since you need the cover for the drive head of a Lippert Edge awning the correct replacement is the part #LC32NJ.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Head Covers for Lippert Solera 2000 Awning

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching