Can You Use the Trailer Frame Attachment on the 12K Trailer Valet RVR12 Remote-Controlled Mover?

Question

Question:

Re. Trailer Valet RVR12: can this be setup with a frame attachment? E.g.: something like the frame connection used on a RVR3. Im asking because I have a Hensley Hitch perma-mounted on my travel trailer, so use of a ball-hitch connection for a RVRx is out of the question. Thanks

asked by: Angus

0

Expert Reply:

Hello Angus,

I reached out to Trailer Valet and they confirmed that you cannot use the plate attachment on the 12K. They don't even sell the plate attachment separately.

Trailer Valet does make a remote control trailer mover with the frame attachments but it is only rated for 3,500 pounds instead of the 12K one you were looking at. It is the Trailer Valet RVR3 Remote-Controlled Trailer Dolly - Wireless Remote - 3,500 lbs # TVRVR3. I attached an image to show how it attaches to the frame of your trailer.

Another option would be the Trailer Valet 5X Swivel Jack and Trailer Mover - Topwind - 15" Lift - 5,000 lbs # STC-V211, this one is not controlled by a remote, but it is rated for 5k, and is also a frame mount.

What kind of travel trailer do you have?

expert reply by: Kate F

0

How the Trailer Valet Connect to Trailer Frame
(click to enlarge)

Kate F.

9/8/2025

Hey Angus, Did you find a suitable solution for your travel trailer with the options I mentioned? I'm eager to hear how it worked out for you, as it might help others in a similar situation.

Answer 1

Trailer Valet actually has a dolly/jack that is designed for attaching to the coupler like you mentioned. For that you'd want the part #TVXL25 for if you have a 2-5/16 inch hitch ball or part #TVXL2 for if you have a 2 inch hitch ball size. I…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Can You Use the Trailer Frame Attachment on the 12K Trailer Valet RVR12 Remote-Controlled Mover?

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching