Replacement Inner Tube For Livestock Trailer

Question

Question:

I need to replace the inner coupler tube on my livestock trailer. My tube has two bolts that go through the front and it is adjustable. Standard ball size. I cant seem to find anything that matches on the website. Can you please help me?

asked by: Dawn P

0

Expert Reply:

The gooseneck inner tube couplers we offer are all designed to work with round 2-5/16 inch balls. The replacement tube you need would depend on the weight capacity you need. I have attached a link to our product page you can check out. Most of the couplers have a 4 inch diameter tube and include the pin assembly. You will want to measure the inside diameter of your outer tube on your gooseneck to make sure you choose the correct replacement inner tube.

expert reply by: Jeffrey L

0

Answer 1

The outer diameter of the outer tube on the Bulldog Gooseneck Coupler part #BD0287600300 is 4-1/2" diameter.

view full answer...

Answer 2

I can absolutely understand not wanting to have to cut off the entire tube, but there just isn't an option for a tube with a coupler that goes over your 4" diameter tube. The reason for that is the inner tubing - the part with the coupler -…

view full answer...

Answer 3

You will need to contact the trailer manufacturer to see if there is a problem with drilling a hole for the pin in the tube on the trailer to use with the #BD0287610300 inner tube. This tube has a diameter of 4 inches so you want to make sure the…

view full answer...

Answer 4

Actually it looks like your coupler uses set screws to stay in position and not a pin like #BD0287610300. So you would actually want the coupler to go in like normal, with the handle on the driver's side, so the set screws make contact with the…

view full answer...

Answer 5

The retracted height of this product #BD0287600300 is 29-1/2", the ball hole is 2-5/16", and has a range of adjustment of 8".

view full answer...

Answer 6

Sounds like you are looking for a replacement inner tube only for your trailer's gooseneck coupler which we have like with the cushioned Convert-a-Ball part #CG. This has an outer diameter of 4 inches which is a very common size and a capacity of…

view full answer...

Answer 7

Since you need a 4 inch diameter pipe the best option we have is the part #BD0287610300 as it has a 4 inch outer diameter whereas the #BD0287690300 that you referenced would be too wide at 4-1/2 inches. Or the part #CG would work too as it is 4 inch…

view full answer...

Answer 8

You would need to contact the trailer manufacturer to see if you can safely use the trailer after drilling a hole for an adjustable coupler such as #BD0287610300. the outer tube would have to have one to use this type of coupler so provided there was…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Inner Tube For Livestock Trailer

Featured Help Information

Miscellaneous Media

Continue Researching