Bulldog Inner Tube Gooseneck Coupler Availability that is 4 inches In Diameter

Question

Question:

Do you sell a trailer coupler like BD0287610300, but without the pin holes? I need one just like your BD0287690300 but will fit up in the 4 inch pipe. I guess the BD0287610300 will work but with my current set up I do not need to or never had to it down

asked by: Patrick L

0

Expert Reply:

Since you need a 4 inch diameter pipe the best option we have is the part # BD0287610300 as it has a 4 inch outer diameter whereas the # BD0287690300 that you referenced would be too wide at 4-1/2 inches.

Or the part # CG would work too as it is 4 inch diameter and has no pin holes.

expert reply by: Jameson C

0

Answer 1

The gooseneck inner tube couplers we offer are all designed to work with round 2-5/16 inch balls. The replacement tube you need would depend on the weight capacity you need. I have attached a link to our product page you can check out. Most of the…

view full answer...

Answer 2

I can absolutely understand not wanting to have to cut off the entire tube, but there just isn't an option for a tube with a coupler that goes over your 4" diameter tube. The reason for that is the inner tubing - the part with the coupler -…

view full answer...

Answer 3

The outer diameter of the outer tube on the Bulldog Gooseneck Coupler part #BD0287600300 is 4-1/2" diameter.

view full answer...

Answer 4

Sounds like you are looking for a replacement inner tube only for your trailer's gooseneck coupler which we have like with the cushioned Convert-a-Ball part #CG. This has an outer diameter of 4 inches which is a very common size and a capacity of…

view full answer...

Answer 5

Actually it looks like your coupler uses set screws to stay in position and not a pin like #BD0287610300. So you would actually want the coupler to go in like normal, with the handle on the driver's side, so the set screws make contact with the…

view full answer...

Answer 6

You will need to contact the trailer manufacturer to see if there is a problem with drilling a hole for the pin in the tube on the trailer to use with the #BD0287610300 inner tube. This tube has a diameter of 4 inches so you want to make sure the…

view full answer...

Answer 7

You would need to contact the trailer manufacturer to see if you can safely use the trailer after drilling a hole for an adjustable coupler such as #BD0287610300. the outer tube would have to have one to use this type of coupler so provided there was…

view full answer...

Answer 8

The retracted height of this product #BD0287600300 is 29-1/2", the ball hole is 2-5/16", and has a range of adjustment of 8".

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Hey Nathan, the PowerMax panels like the part #PM59VR that you referenced use 12- VAC residential style miniature circuit brakers. Typical brands are ITE/Siemens, Murray, Crouse-Hinds, and Thomas & Betts.

view full answer...

Bulldog Inner Tube Gooseneck Coupler Availability that is 4 inches In Diameter

Products Featured in This Question

Continue Researching