Parts for Single Round Yakima Crossbar Setup on a 2025 Chevy Silverado 1500

Question

Question:

I am trying to change the air flow over my 2025 Silverado with a Scout truck camper in the bed. I have a single core bar and will be purchasing an air screen. What clip kit will I need and can I purchase just two? Any advice on an air screen for my vehicle would be appreciated also. Thanks

asked by: David

0

Expert Reply:

Hey David, thanks for reaching out!

We can definitely get your 2025 Chevy Silverado 1500 set up with 1 CoreBar, just be sure it's at least 58" long to completely cover the width of your truck cab. Aside from the bar, here are the other parts you'll need:

- BaseLine Towers # Y62TR
- Fit Kit # Y06110

The towers and fit kit are half kits so you won't have any extra parts lying around.

As for the fairing, Yakima recommends the 52" Long Fairing # Y05019 for your truck, so that will give you the best coverage.

Let me know if you have any other questions!

expert reply by: Jon G

0

David D.

4/18/2025

Hi Jon I see you are referring to a round bar setup and your research is appreciated. I have a Yakima core bar that would be used with the towers. My question is what clip kit do I need to attach the towers to my 2025 Silverado 1500. Thanks.

Jon G.

4/18/2025

@DavidD Whoops, sorry about that! In that case, you'd use the exact same parts, minus the SL Adapter that would be for the round crossbar. I'll go ahead and get the answer updated for future readers as well. Thanks for reaching back out!

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Parts for Single Round Yakima Crossbar Setup on a 2025 Chevy Silverado 1500

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching