What is the Eye to Eye Length on the Yakima Heavy Duty Shocks for Rack and Roll Trailers

Question

Question:

What is the shock length from eye-to-eye on the Y08110 trailer shocks?

asked by: Tod

0

Expert Reply:

I went out to the warehouse and pulled Yakima shock for Rack and Roll trailers # Y08110 to measure it. From the center of one eye to the center of the other is approximately 12-7/8 inches.

expert reply by: Michael H

0

click to enlarge

Answer 1

If you check out the picture I attached you will see where I pointed out where the sticker is that has the VIN on the Yakima Rack and Roll trailers like the part #Y08106. If somehow the sticker is worn off or unreadable my contact at Yakima said that…

view full answer...

Answer 2

Replacement Left Side Fender for Yakima Rack and Roll Trailers - Qty 1 #Y8880164 and right side #Y8880163 are intended to be priced equally. The reason why they are not at this moment is that the right fender is on sale in our system. Why they both…

view full answer...

Answer 3

The max boat length for the Yakima Rack and Roll Trailer part #Y08106 is 17' per Yakima. It would probably work just fine with a slightly longer boat but we cannot recommend this. That said, there is another trailer that will work better for you…

view full answer...

Answer 4

According to Yakima, the Heavy Duty Shocks for Yakima Rack and Roll Trailer #Y08110 should only be used if you add the 78" crossmember kit #Y08111. They didn't have an exact reason for this, but it sounds like the concern is people will…

view full answer...

Answer 5

While there isn't a life expectancy, per se, of the shocks on the Yakima Rack and Roll Trailer - 66" #Y08106 and 78" #Y08107, upgrading to the HD shocks is absolutely a good idea if your gear weighs around 200 llbs and certainly…

view full answer...

Answer 6

I reached out to my contact at Yakima and she said that the compressed length of the Replacement Standard Shocks #8880177 is 9.45 inches. These are designed to replace the standard shocks on the Yakima Rack and Roll Trailer #Y08106 and #Y08107.

view full answer...

Answer 7

The Replacement Tongue for Yakima Rack and Roll Trailer #8880204 is 3/16" thick. The overall dimensions are 69-5/8" long x 2" wide x 2" tall.

view full answer...

Answer 8

Since we have started carrying the Yakima Rack and Roll trailer #Y08107 I have not heard any complaints regarding the wheel bearings failing and only a few instances where people wanted to replace the wheel assembly. If you need to replace your…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

What is the Eye to Eye Length on the Yakima Heavy Duty Shocks for Rack and Roll Trailers

Product Page this Question was Asked From

Continue Researching