Is there a Method or Trick to Hole Nylon Nut in Place when Installing New Motor Series 25 Steps?
Updated 04/14/2025 | Published 04/09/2025 >
Question:
Ok, so I was able to get the old motor off my series 25 triple steps, but I’m not sure how to install the new motor? The nylon nuts that the bolts screw into, are placed above a plate, within a small hole where the nut threads are visible, and but in an inconvenient location. Along with a small metal bushing for each bolt, Is there a simple method or trick in order to be able to hold the nylon nut in place to screw the bolt in? Just looking at it, it look’s difficult. Thanks for any help.
asked by: Jim
Expert Reply:
Hello Jim,
Installing the new motor # LC369506 on your Series 25 triple steps can be a bit tricky, especially with those nylon nuts hiding up in that little hole. They’re in a tight spot, and it’s hard to hold them still while trying to screw in the bolts, plus those little metal bushings just make things more annoying. But don’t worry, there are some simple tricks that can really help.
One good method is to use a pair of small locking pliers (like needle-nose Vise-Grips). If you can reach the nut from above or the side, clamp the pliers on it and lock them in place so the nut doesn’t spin while you put the bolt in. If the nut or bushing is magnetic, you can try using one of those extendable magnet tools to hold it steady too.
Another easy trick is using painter’s tape or masking tape. Just tape the nut and bushing in place over the hole, then poke the bolt through the tape to get it started. Once it catches the threads, you can pull the tape off. Some folks also use a dab of thick grease or even a little glue dot to help hold the nut in place just long enough to get the bolt started.
If it’s really tight in there, using a flexible tool extension or a small ratchet can make it easier to reach. And sometimes it helps to loosely put the bolts and nuts on the motor first, then carefully fit the whole thing in place and tighten everything once it’s lined up.
Let me know if one of those tricks was helpful for you.
Product Page this Question was Asked From
Replacement Motor for Kwikee 25 Series Electric RV Steps - 12V
- Accessories and Parts
- RV Steps
- Motors
- Kwikee
more information >
Continue Researching
- Search Results: rv step stabilizer
- Shop: Replacement Motor for Kwikee 25 Series Electric RV Steps - 12V
- Video: Detailed Breakdown of the Replacement Motor for Kwikee 25 Series Electric RV Steps
- Video: The Low-Down on the Replacement Motor for Kwikee 25 Series Electric RV Steps
- Shop: Replacement Motor for Kwikee Electric RV Steps - 12V
- Shop: Replacement Motor with Gear and Table for Kwikee 24 and 25 Series Electric RV Steps
- Video: Replacement Motor with Table for Kwikee 25 Series Electric RV Steps: The Breakdown
- Video: Review of Kwikee RV and Camper Step Gear - LC369354
- Shop: Vehicle Seat Covers
- Shop: Replacement Control Unit for Kwikee Revolution Series Electric RV Steps
- Q&A: Recommended Driver And Passenger Seat Cover For Captain Chair on 2012 Thor Ace 29.2
- Shop: Replacement Crossbar Installation Hardware for Yakima OverHaul HD and OutPost HD Truck Bed Racks
- Shop: Replacement Motor for Lippert Electric Coach Step
- Shop: Replacement Motor with Table for Kwikee 25 Series Electric RV Steps
- Q&A: Troubleshooting Motor On Kwikee Steps Continuing To Run After Steps Are Fully Opened Or Closed
- Q&A: Replacement Control Unit for Kwikee Revolution Series Steps
- Q&A: What is Purple Wire For on Replacement Control Module for Lippert Kwikee Steps
- Video: The Low-Down on the Replacement Control Unit for Kwikee Revolution Series Electric RV Steps
- Q&A: Replacement Motor Recommendation for RV Step Kwikee 25 Model
- Q&A: Replacement Gear and Motor Recommendation for Kwikee 25 Series RV Step
- Q&A: Replacement Motor for the Lippert Components Kwikee Triple Entry Steps # LC3658373
- Video: Review of Thomas Payne RV Couches and Chairs - Triple Reclining RV Couch Drohan Cement - TP38KR
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement


Jim
4/11/2025
Thanks Kate, would you happen to have a diagram of how the bushing and nut are situated (what order). When I took the motor off they fell down and I don't remember what the order was for the bushing and nut? I also saw another post that said to take off the gear table and that would allow access to the top of the plate. May try that also. Thanks,