Diameter of Center Shaft that Holds Handle on Pro Series Round Topwind Jack PS1400300303
Published 11/14/2019
Products Featured in This Question
Question:
What is the diameter of the shaft protruding from the top of the jack where the crank is attached.
asked by: Michael W
Expert Reply:
I went out and to our warehouse and measured the center shaft on one of our Pro Series Round, Snap-Ring Swivel Jack Topwind # PS1400300303. The shaft is 1/2 inch in diameter.
If you're looking for a replacement handle, the Replacement Handle for Top Wind Style Trailer Jacks # DL22674 will work well as it use the same size (1/4 inch) hardware and is right at about the same length (7 inches). Pro Series does not offer a direct replacement jack handle.
If that's not what you're after, let me know what you're trying to do to see if I can come up with a solution for you.
Product Page this Question was Asked From
Pro Series Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10" Lift - 2,000 lbs
- Trailer Jack
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Standard Grade
- 1001 - 2000 lbs
- Manual Jack
- 10 Inch Lift
- Bolt-On
- With Rectangle Foot
- Pro Series
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: atwood tongue jack
- Q&A: Recommended Bulldog Trailer Jack That Installs With a Snap-Ring, 15" Lift, and 2,000 lb Capacity
- Search Results: waste valve cap
- Search Results: scamp
- Search Results: handle
- Search Results: c clip
- Search Results: valterra
- Search Results: trailer jack handle
- Shop: Valterra Threaded RV Sink Drain - Fits 1-3/4" Diameter Drains
- Shop: RV Shower Drain with Strainer - 2" Diameter - Chrome Plated Steel
- Shop: RV Shower Drain with Strainer - 2" Diameter - Chrome Plated Steel
- Shop: Replacement Snap Ring for Bulldog Snap-Ring Swivel Jacks - Qty 1
- Shop: Replacement Retaining Ring for Curt Snap Ring Swivel Jacks
- Shop: Round Snap Ring Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 10-1/2" Travel - 2K
- Shop: Round Snap Ring Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 15-1/4" Travel - 2K
- Video: Comprehensive Review: LaSalle Bristol RV Sewer Termination Adapter
- Video: The Low-Down on the Replacement Handle for Top Wind Style Trailer Jacks by Dutton-Lainson
- Video: Valterra Drip Cap and Waste Valve Cap for RV Sewer Hose: The Breakdown
- Video: An In-Depth Look at the Valterra Threaded RV Sink Drain
- Video: All You Need to Know About the Landing Gear Set
- Video: Bulldog Bolt-Thru Swivel Trailer Jack Review
- Video: Bulldog Round, Snap-Ring Swivel Jack: The Breakdown
- Q&A: What is the Preferred Method of Connecting Safety Chains from a Trailer to a Trailer Hitch
- Q&A: Replacement Caliper for Tie Down Engineering 46802
- Q&A: Torque Specification for Lugs Nuts on 5/8-Inch Stud on Dexter Hub
- Q&A: How to Use Brake Controller Install Harness from 2002 Chevy Silverado on 2004 Chevy Suburban
- Q&A: Trailer Brake Controller Wiring Harness for a 2003 Chevy Silverado
- Q&A: Is There an Adapter to Mount the Ultimate Trailer Jack to a Side Mount Bracket on Trailer?
- Article: Best 2020 1/2-Ton Trucks for Towing a 5th Wheel
- Article: Trailer Lighting Requirements
on Trailer Jack
