Looking For Replacement Swivel Jack For 1984 Scamp Trailer
Updated 11/10/2026 | Published 06/09/2025 >
Question:
Friends: We possess a 1984 Scamp Trailer. We wish to replace the trailer hitch jack. It is a side-mounted easy-swivel top-wind jack with an Atwood handle. It has a solid foot. The jack is attached to the frame via a bracket that is welded to the frame. What do you and I need to know replace the jack unit only without having to replace the welded bracket? Preferably the replacement would have a side-wide system and either a wheel or the ability to swap foot and wheel.7
asked by: Brett N
Expert Reply:
Hello Brett, thanks for reaching out. I looked online at a few pictures of these 1984 Scamp Trailers. Most of the pictures I saw showed a snap ring swivel jack, so it sounds like that is what you are looking for. Something like the Round Snap Ring Swivel Jack w/ Footplate # TJB-2002-B. This uses a standard mounting bracket that measures 4" wide by 5" tall and uses a 1/2" spring loaded pin. Please check your trailer and verify this matches.
If this is not exactly what you are looking for, let me know. You can even feel free to email me a few pictures of your specific jack and I am happy to take a look. Also if you can tell me the retracted/extended length of your jack that will help a lot.
Replying on this page is the fastest way to get ahold of me.

Judson
11/9/2026
I'm in the same boat with my 1985 Scamp. Did the one you recommend end up working for the guy with the 84 scamp?

Continue Researching
- Shop: Trailer Valet Boat Jack w/ Wheel - Sidewind - Swivel - 10" Lift - 1,000 lbs
- Search Results: cooktop rv stoves and ovens
- Shop: Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - 1,500 lbs
- Shop: Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 12" Lift - 1,000 lbs
- Q&A: Diameter of Center Shaft that Holds Handle on Pro Series Round Topwind Jack PS1400300303
- Q&A: Recommended Bulldog Trailer Jack That Installs With a Snap-Ring, 15" Lift, and 2,000 lb Capacity
- Search Results: atwood tongue jack
- Shop: RV Shower Drain with Strainer - 2" Diameter - Chrome Plated Steel
- Shop: RV Shower Drain with Strainer - 2" Diameter - Chrome Plated Steel
- Shop: Round Snap Ring Swivel Trailer Jack w/ Footplate - Topwind - 15-1/4" Lift - 2,000 lbs - Weld
- Shop: Valterra Threaded RV Sink Drain - Fits 1-3/4" Diameter Drains
- Q&A: What is the Preferred Method of Connecting Safety Chains from a Trailer to a Trailer Hitch
- Video: What to Know About the Laclede 35" Long Trailer Safety Chain w/ Clevis Slip Hook
- Video: Hands-On with the Laclede 35" Long Trailer Safety Chain w/ Clevis Slip Hook
- Video: Comprehensive Review: RV Shower Drain with Strainer
- Search Results: filter
- Video: The Low-Down on the Replacement Handle for Top Wind Style Trailer Jacks by Dutton-Lainson
- Video: Valterra Drip Cap and Waste Valve Cap for RV Sewer Hose: The Breakdown
- Video: Comprehensive Review: LaSalle Bristol RV Sewer Termination Adapter
- Search Results: trailer jack handle
- Search Results: handle
- Search Results: valterra rv waste valves
- Search Results: waste valve cap
- Video: An In-Depth Look at the Valterra Threaded RV Sink Drain
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Shop: Trailer Wiring

Bn
6/20/2025
Thank you for the very thorough reply. Much appreciated. You are correct that the jack is held to the welded plate by a cee clip/snap ring. However, the current jack uses spring loaded locking pins that are 3/8". The exterior measurement as installed is 2&15/16" in the outer diameter. I can't measure the interior diameter without uninstalling the jack at this point. My guess is 2.5" The welded bracket is 4&1/4" t-b and s-s. Any help identifying a replacement that would allow use of current welded bracket would be appreciated. Brett