Looking For Replacement Brakes And Hubs For Interstate Trailer

Question

Question:

i have a interstate trailer , vin 1UK500G22G1089065. could you tell me what bearing kits and electric brakes i need for this trailer . thanks

asked by: Stephen E

0

Expert Reply:

Hello Stephen, thanks for reaching out. We should have the parts you need, but unfortunately we do not have a way to reference a VIN number to know what parts you need. Trailers are not standardized like motor vehicles, and trailer manufacturers just do no list this kind of info online.

There are a few pieces of info that can help me narrow it down. if you can tell me the axle weight capacity that will help a lot find the brakes.

As far as the bearings and hubs, you best bet will be to pull a hub and remove the bearings. Each bearing will have a number stamped on the edge, or you can measure the ID with a micrometer. Also measure the ID of your seal. I will also want to confirm your hub bolt pattern.

Leave that info in a reply below and I am happy to look into it and get back to you.

expert reply by: Jesse M

0

Jesse M.

10/27/2025

Hey Stephen, were you able to check the axle capacity and get the bearing numbers from your Interstate trailer? Once you have those details, I can help narrow down the right bearing kits and brakes. Let me know what you find so we can get you the right fit.

Answer 1

If you have a 3,500 lb Dexter EZ Lube spindle we for sure have the parts needed to add brakes to your trailer or replace ones that you currently have. For a set of 10 inch assemblies that would fit and work well you'd want the part #AKEBRK-35-SA…

view full answer...

Answer 2

We don't have any way of knowing the brakes you need for your Shorelander boat trailer but can tell you how to determine the right ones. To determine the brake assemblies that will fit your trailer, you need to know your axle's weight…

view full answer...

Answer 3

We offer both complete electric brake assemblies and replacement parts for them. Often it is more cost-effective to replace the entire brake assembly than to purchase the various replacement parts to repair one but we can help with either option.…

view full answer...

Answer 4

We can help you select replacement electric drum brakes for your Sundowner horse trailer. You can usually find an axle's capacity on a sticker or plate on the axle itself. You'll naturally want to choose replacement drum brakes that match…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Looking For Replacement Brakes And Hubs For Interstate Trailer

Product Page this Question was Asked From

Continue Researching