Installation Instructions and Video for the Pro Series Weight Distribution Head part # PS58442

Question

Question:

Are there printed instructions on how to attach he head assembly to a shank. I want to make sure I put the hardware in its designed positions/locations. Thank you

asked by: Mark C

0

Expert Reply:

There aren't printed instructions, but there is a diagram that I attached that shows how all the pieces install together.

For further setup info check out the installation instructions I attached for the Weight Distribution system part # PS49583 and the install video that details how to install and setup this system. The WD head part # PS58442 that you referenced is the head of assembly of the part # PS49583.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Rick, yes you can just swap out the shank that you have now for one that is designed for a 2-1/2 inch hitch like the Blue Ox part #BXW4028. You probably already know this but you'll most likely need different spring bar tension on the new…

view full answer...

Answer 10

Hey Mark, the only real downside to an offset ball like the Gen-Y part #GY43XR is going to be that it costs more typically and it would take up more room when stored compared to a non-offset ball like the #C38CR. The handling and weight carrying…

view full answer...

Answer 11

Hey Richard. The MORryde GooseTech 5th Wheel to Gooseneck Pin Box like item #MR27MV has not been approved for use by Grand Design. It does not fall under their 5-year limited towable frame warranty that applies to the 2020 and newer 5th wheel…

view full answer...

Answer 12

Hey JC, thanks for reaching out! The B&W Tow & Stow 2-Ball Mount #BWTS20066BMP is definitely compatible with the MultiPro tailgate on your 2024 GMC Sierra 2500, but the only one available to fit exactly with a 2-1/2" hitch receiver is…

view full answer...

Installation Instructions and Video for the Pro Series Weight Distribution Head part # PS58442

Featured Help Information

Miscellaneous Media

Continue Researching