Availability of Trailer Jack That can Attach to Angle Iron
Updated 10/27/2025 | Published 03/13/2025
Question:
I have a utility trailer made of angle iron, the frame is 3 x 2. I want to find a jack that I can mount to the angle frame so I can remove the A jack. I can weld, if need be, but would prefer bolt on. Any suggestions?
asked by: Ron
0
Expert Reply:
Hey Ron, we don't have any bolt on style jacks that will attach to angle iron so you would need to weld on a mount like what comes with the Round Snap Ring Swivel Jack w/ Footplate # TJB-2001-Z. Does it have an a-frame jack currently?
expert reply by:
Jameson C
0
Product Page this Question was Asked From
Round Snap Ring Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 10-1/2" Travel - 2K
- Trailer Jack
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Topwind Jack
- 1001 - 2000 lbs
- Manual Jack
- 11 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Continue Researching
- Q&A: Trailer Jack Recommendation or Trailer with Angle-Iron Frame
- Video: All About the etrailer Spare Tire Mount for Trailer with Angle-Iron Railing
- Shop: etrailer Spare Tire Mount for Trailer with Angle-Iron Railing - Clamp On
- Q&A: Can etrailer Swivel Jack be Install to Angle Iron on Homemade Trailer?
- Shop: Round Snap Ring Swivel Jack w/ Footplate - Weld On - Zinc - Topwind - 10-1/2" Travel - 2K
- Video: Review of etrailer Trailer Jack - Car Hauler - Enclosed Trailer - Utility Trailer - e22ZV
- Shop: etrailer Swivel Jack w/ Bolt-On Mounting Plate - Sidewind - 10" Travel - 3,000 lbs
- Video: Complete Breakdown of the Fulton Boat Trailer Jack w/ Wheel
- Search Results: swivel jack
- Shop: etrailer Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1,000 lbs
- Video: Breaking Down the Weld-On Barrel Hinge with Grease Zerk
- Shop: Weld-On Hinge w/ Brass Bushing and Grease Zerk - Steel - 10-1/4" Long - 3/4" Pin Diameter
- Shop: Weld-On Barrel Hinge with Grease Zerk - Round Body - Steel - 4-3/4" Long - 3/4" Diameter
- Search Results: spare tire mount
- Search Results: hp29fr
- Video: Single Axle Trailer Fender w/ Backing Plate Spec Review
- Video: Single Axle Trailer Fender w/ Backing Plate Review
- Shop: Single Axle Trailer Fender w/ Backing Plate - Steel - 14" to 15" Wheels - Qty 1
- Q&A: Converting 18' Flatbed Trailer From Surge Brakes To Electric Over Hydraulic Brakes
- Q&A: Installation of Emergency Break Away Cable Repair Kit for Dexter Axle A-60 Brake Actuators
- Q&A: What Mounting Bracket Is Needed for the Round Snap Ring Swivel Jack TJB-2001-Z
- Q&A: Are Shackles Necessary For A Single Axle Utility Trailer?
- Q&A: Replacement Hardware To Install Curt C13379 Class III Hitch on 2011 Ford Taurus
- Article: Trailer Tire Sizing
- Article: Trailer Lighting Requirements
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Article: Most Popular Wheel Bearings
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure a Trailer Axle
Explore Expert Info
![Our Expert]()
on Trailer Jack
on Trailer Jack
Jameson C.
10/27/2025
Hey Ron, did you end up welding on the mount for your trailer jack? Knowing how that setup worked could help others trying to fit a jack to an angle iron frame.