Replacement Fulton Swivel Sidewind Jack for Boat Trailer

Question

Question:

Hi, I need to replace the Fulton jack on my 2013 Skeeter trailer. Boat is a FX21. It is a bolt through on a welded bracket. Would much appreciate a recommendation. Photo is attached. Thx

asked by: Greg D

0

Fulton Boat Trailer Jack
(click to enlarge)

Expert Reply:

Hey Greg, thanks for the picture of your jack! From that I can tell pretty easily that what you need is the Fulton Boat Trailer Jack part # FXP100W0301.

expert reply by: Jameson C

0

Jameson C.

10/27/2025

Hey Greg, how did the Fulton boat trailer jack work out on your Skeeter trailer? Knowing how the fit turned out could help others replacing the same style jack.

Answer 1

Hey George, best solution for you will be to go with an all new jack like the etrailer part #e95YV because Fulton is no longer in business so there isn't a way to get a replacement F2 and none of the other jacks out there use the same bolt…

view full answer...

Answer 2

Hi George; there are some replacement parts available for the Fulton F2 Boat Trailer Jack #F1413020134. We have the following: -Replacement Handle and Crank Kit for Fulton F2 Swing-Up Jacks #F500134 -Replacement Pull Pin Kit for Fulton F2 Swing-Up…

view full answer...

Answer 3

I spoke with my buddy at Tekonsha, who is our leading supplier of brake controllers. He cited two possible issues that could be causing your problem. First, the trailer brakes work best when they have a little heat in them, so to speak. If you pull…

view full answer...

Answer 4

Fulton bolt-through trailer jack #F1411300301 is the only Fulton jack that mounts using that 1 center bolt. Since your old jack was a Fulton it must either be this same jack or an earlier model but they use the same mount. The mount in question and…

view full answer...

Answer 5

We do have a potential option for you, but the Curt Anti-Rattle Hitch Clamp #C87UR is likely not going to work with your setup. I think you are exactly right in that there is really no room between the receiver and the hitch. So there is really…

view full answer...

Answer 6

Hello Josh, I am glad you ordered the Titan Chain Screw Pin D-Shackle - Galvanized - 5/16" Diameter - Qty 1 #TCS8MM because it is going to work great for you. The inside opening is about 5/8" so it will be able to handle your 9/16"…

view full answer...

Answer 7

The Fulton Bolt-Thru Swivel Marine Jack #F1411300301 will definitely work for you as a replacement for the current Fulton Magnum Series jack you have, as it will mount to the bracket already on your trailer, as that bracket will be the Jack Mounting…

view full answer...

Answer 8

I do not see something we carry that would be an exact replacement. If you can give me your jack's model number it would help me find if we have something that will work for you because the replacement mounting brackets match up to certain…

view full answer...

Answer 9

The jack I recommend to replace your Fulton 1000 lb jack with bolt through is the Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,500 lbs #FXP15W. This is a very sturdy jack that will give you a little added safety as you…

view full answer...

Answer 10

Based on the picture you submitted the Fulton Marine Jack part #FXP100W0301 that you referenced would be exactly what you'd need and would bolt right up to the mount you have on the trailer frame.

view full answer...

Answer 11

The only trailer jack that will work with your existing mounting bracket and not contact the boat with a full rotation of the handle is the Fulton Bolt-Thru Swivel Marine Jack part #F1411300301. I understand this does not have the sharkskin coating…

view full answer...

Answer 12

If the holes on your mount are separated by 3 inches the Fulton trailer jack #FXP100W0301 will fit. If you need a new mount you'd need the #P9012-00. For new hardware for the bracket you'd need the #F0933325S00.

view full answer...

Replacement Fulton Swivel Sidewind Jack for Boat Trailer

Continue Researching