Orientation of Rear Hanger Installation on a Trailer with Double Eye Leaf Spring Suspension
Updated 07/06/2024 | Published 06/07/2014
Question:
I received the kit and was laying things out when I noticed that the rear hanger is not symmetrical. The bushing is off to one side and not centered in the fitting. There is a stamping on the part that says TOP. Which side of the hanger is forward? What am I missing? Thank you
asked by: Stephen V
Expert Reply:
The portion of the rear hanger with TOP labeled on it will get welded to the trailer frame.
I am including a picture of the hangar that shows the top marking and how it is positioned on the trailer.
I attached an FAQ on trailer suspension for you to check out also.
Product Page this Question was Asked From
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 7/8" Rear
- Trailer Suspension Parts
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Single Axle
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: jack
- Search Results: coupler
- Search Results: hanger kit
- Search Results: spring
- Search Results: leaf spring
- Q&A: Installing Leaf Springs on Single Axle Trailer
- Shop: Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 7/8" Rear
- Video: Single-Axle Trailer Hanger Kit for Double-Eye Springs: The Breakdown
- Q&A: Should Suspension Shackle Straps Angle Towards the Front or Rear of a Trailer
- Q&A: How to Install Spring Hangers on Single Axle Trailer
- Shop: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs
- Shop: Dexter Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 38" Axle Spacing
- Shop: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long - EMCO
- Shop: Dexter Heavy Duty Suspension Upgrade Kit for Single Axle Trailers -3-1/8" Shackle Straps
- Shop: 6-Leaf Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long
- Shop: etrailer 2 Swivel Jacks w/ Bolt-On Mounting Plates - Sidewind - 15-1/2" Lift - 3,000 lbs
- Shop: Trailer Wiring
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Video: Review of The Hub Saver Trailer Bearings Races Seals Caps - Hub Wheel Protector - HS79FR
- Search Results: trailer wiring harness
- Search Results: trailer wiring
- Q&A: Can I Use Heavier Rated Leaf Springs on Trailer Without Causing Damage
- Video: Review of RV Designer Trailer Lights - Clearance Lights Amber - RD69RR
- Article: Double-Eye Trailer Suspension System Review
- Article: How to Replace Trailer Leaf Springs in 5 Steps
- Q&A: How Tight Should Shackle Bolts Be Tightened On Trailer
- Q&A: What Gauge Wire Is The 30 ft. Wishbone 4-Way Trailer Wiring Harness A30WB?
- Q&A: What is Torque for 3,500 lb Axle U-Bolts
- Video: Review of TowSmart Custom Fit Vehicle Wiring - 7 Way RV To 4 Way Flat Connector Adapter - TS62SR
- Video: This Old Trailer: Replacing Leaf Springs
Tom
7/4/2024
I have these hangers on my single 6000lbs axle. There are 3000lbs rated springs on each side. Are these hangers rated for that?