Do the Shackle Straps Go Inside or Outside the Leaf Spring Hanger
Updated 12/17/2018 | Published 12/16/2018 >
Products Featured in This Question
Question:
When mounting the rear leaf spring shackles on a single axle boat trailer, should the shackles be outside the fixed hanger or inside. I have them inside the hanger currently and they are closer together between the hangers. If I mount them on the outside the will be farther apart. I have 25 1/4 double eye springs and shackles. There is 2 inches between the hangers.
asked by: Jack
Expert Reply:
The shackle straps need to be placed on the outside of the rear leaf spring hangers which you can see in the attached photo. Furthermore, the distance between the two mounting plates (inside to inside) on your leaf spring hangers should be 1-7/8", not 2" which is most likely why there is too much of a gap between the shackle straps and leaf spring. Therefore, the leaf spring hangers will need to be replaced.
For this, we generally kit the single axle trailer suspension hangers and shackle straps together like the Single-Axle Trailer Hanger Kit for Double-Eye Springs part # APS4 or part # APS2 to make things easier so this is what I recommend using.
Product Page this Question was Asked From
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
- Trailer Suspension Parts
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Single Axle
- etrailer
more information >
Continue Researching
- Shop: Trailer Wiring
- Shop: Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear
- Shop: Gooseneck Hitch
- Search Results: curt 56070
- Search Results: lm67048
- Video: A Closer Look at the Single-Axle Trailer Hanger Kit for Double-Eye Springs
- Shop: etrailer Rust-Resistant 3-Leaf Double Eye Spring for 2K Trailer Axles - 20-3/8" Long - Dacromet
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Shop: Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Shop: Curt Pop-In Ball for Factory Chevy/GM, Ford, Nissan, and Ram Underbed Gooseneck Hitches - 3"
- Shop: Base Plate for Tow Bar
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
- Search Results: idler hub
- Search Results: junction box
- Search Results: trailer backup lights led
- Shop: Suspension Enhancement
- Search Results: taillight
- Search Results: bearing buddy bra 17b
- Q&A: How To Install a 7-Way and Brake Controller On a 2020 Toyota Highlander
- Q&A: Dimensions of U-Bolt # CE15504A
- Q&A: How To Install Roller Bunks on a Malone Watersport Trailer
- Shop: Front/Rear Hanger for Double-Eye Springs - 1-5/16" Tall - 9/16" Bolt Hole
- Article: How to Replace Trailer Leaf Springs in 5 Steps
- Article: Adding Electric Over Hydraulic Disc Brakes
- Shop: Tool Box
- Shop: Truck Bed Auxiliary Tank
- Video: 3-Leaf Double-Eye Spring for 2,500-lb Trailer Axles Review
- Video: The Low-Down on the Single-Axle Trailer Hanger Kit for Double-Eye Springs
- Video: What to Know About the Shackle Bolt For Double-Eye Springs
- Video: Trailer Axle with Idler Hubs Spec Review


