What is Wire Gauge of Replacement Inner Member Lock Out Solenoid

Question

Question:

What is the back up solenoid wire size 14 16 ?

asked by: Ken

0

Expert Reply:

Hey Ken, the wire gauge of the lock out solenoid on the replacement inner member part # DX99FR is 16 gauge.

expert reply by: Jameson C

0

Jameson C.

10/30/2025

Hey Ken, did the 16-gauge wire on the lockout solenoid work well for your setup? Knowing how it performed could help others wiring the same actuator.

Answer 1

I am not quite sure what you have on your UFP A-160 actuator but if you check out the attached picture the only way you can manually lock out an actuator is if it has a manual lockout built-in. Technically you can drill a hole in the side of it and…

view full answer...

Answer 2

Hey Mark, welcome back! If your 2013 Ranger Bass Boat Trailer has a UFP Model A-60 Marine Surge Brake Actuator similar to item #DX89FR, you can replace it with the Inner Member for Dexter DX7.5L Actuator item #DX99FR, you were looking at. The Inner…

view full answer...

Answer 3

Dexter doesn't put reverse lock outs on their drum brake actuators so you'd need to add the part #DM5404 do a new actuator. The part #DX97FR is just the inner section of an actuator though. For the actuator you'd need the part #DX33FR.

view full answer...

Answer 4

It sounds like you are looking for the Replacement Inner Member #DX97FR. This is for drum brakes and does not have a reverse solenoid like the Inner Member #DX99FR you found.

view full answer...

Answer 5

Hello Gregg, I think I can help shed some light on what is going on. Basically, there are two ways to stop surge brakes from actuating when backing up the trailer. The first and most popular way to do this is to use a surge brake actuator with a…

view full answer...

Answer 6

Reverse lock out solenoids are not polarity sensitive so you could run either the white or the blue wire of the Dexter coupler part #DX99FR as the power or ground and you'd be totally fine.

view full answer...

Answer 7

We do have both the Inner Member #DX97FR and Master Cylinder #TK71-756-00 for your Dexter A-60 drum brake actuator. These both have the aluminum construction you are looking for.

view full answer...

Answer 8

Hi Joshua; you can respond to the email that had the link for this page if you want to send me the video. It does sound like it is the actuator, could be the shock in there or the master cylinder. It would also be worth checking to see if the brake…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

What is Wire Gauge of Replacement Inner Member Lock Out Solenoid

Product Page this Question was Asked From

Continue Researching