Hitch Height of PullRite SuperGlide 5th Wheel Hitch for Chevy/GM Factory Prep Package

Question

Question:

Will this hitch fit under a bed cover

asked by: Cosmo M

0

Expert Reply:

Hey Cosmo, thanks for reaching out!

The PullRite SuperGlide 5th Wheel Hitch # PUL83RR has a 18-3/8" hitch height, so as long as your cover doesn't sit lower than that to your 2023 Silverado 2500 bed then this will fit just fine. Tonneau covers sit at varying heights though, which is why I can't answer this specifically.

This hitch does require a capture plate, so if you can let me know what pin box your 5th wheel is equipped with, I'd be more than happy to tell you what capture plate you need so you'll be all set!

expert reply by: Jon G

0

Cosmo M.

1/17/2025

I am thinking about getting a new pin box which one will go with this hitch

Jon G.

1/17/2025

@CosmoM Pretty much any pin box will work with the SuperGlide, really. What is your pin box number? This should be located on a sticker on the side of the box and it will be a 4 digit number like 1621 or 0719. If you can let me know what that number is, or even the serial number on your pin box, I can make a replacement recommendation for you.

Cosmo M.

1/18/2025

@JonG s/n 2022119569 curt turning point

Jon G.

1/24/2025

@CosmoM Sorry for the delayed response, I've been reaching out to Lippert and PullRite to make sure I get you accurate information. The great news is that you don't need any capture plate for the Turning Point pin box! You just need to use the wedge that came with your pin box and flip it so the long side is facing the king pin and you'll be good to go!

Answer 1

Hi Eric; the correct capture plate for the PullRite SuperGlide 5th Wheel Hitch #PUL83RR depends on the pin box on your 5th wheel. The manufacturer can identify it if you get the serial number off of the pin box sticker or you can measure the bolt…

view full answer...

Answer 2

Hi Jake; the PullRite SuperGlide 5th Wheel Hitch #PUL83RR is what you need for your 2025 Chevy Silverado 2500. This will drop right into the pucks from your OEM prep package. You will also need a capture plate like the #PUL46RR. The right one depends…

view full answer...

Answer 3

Hey Steve! The PullRite SuperGlide #PUL83RR will not contact the tailgate on your 2025 GMC Sierra 2500. They have tested this extensively and said making contact and causing damage is not a concern. This is a really great hitch and autoslide is the…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hey Doug, welcome back! Yes, we have the Andersen Ultimate Safety Chain Kit with Clevis Hooks #RM3230. This is the complete kit, Andersen doesn't have the attachments available individually. It is specifically designed for the gooseneck mount…

view full answer...

Answer 11

Welcome back Anthony! The Curt parts you were looking at are compatible with your Silverado and each other but I recommend the B&W Companion OEM 5th Wheel Hitch w/ Slider item #BWRVK3775. The B&W Companion w/ Slider item #BWRVK3775 is one of…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Hitch Height of PullRite SuperGlide 5th Wheel Hitch for Chevy/GM Factory Prep Package

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching