How Much Does The Gen-Y Torsion 2-Ball Mount 325-GH-1225 Weigh?

Question

Question:

What is the weight of this hitch?

asked by: Michael S

0

Expert Reply:

Hello Michael, thanks for reaching out. The Gen-Y Torsion 2-Ball Mount # 325-GH-1225 weighs 84 lbs altogether including the ball mount, ball attachment and pintle lock.

expert reply by: Jesse M

0

Jesse M.

11/17/2025

Hey Michael, did the 84‑lb Gen‑Y Torsion 2‑Ball Mount end up being a good fit for your towing setup? Knowing how it worked could help others decide if that weight is manageable for their rigs.

Answer 1

To determine the correct shank for your weight distribution hitch, you need to find the rise or drop you need, just like with a standard ball mount. This is only two measurements - first, measure from the ground to the top of your hitch receiver…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hey Steve, welcome back! The difference between these two Hellwig Adjustable Big Wig Rear Anti-Sway Bars is the fitment. The #HE94FR is designed for 4WD models and the #HE97MR is designed for 2WD models. Since your 2019 F-250 is 4WD you need the…

view full answer...

Answer 11

Hey Steve, thanks for reaching out. The Thomas Payne Trifold RV Loveseat and Sleeper #LC92PX is approximately 70" long with the bed extended out. Will that fit in your living room? Is it more for a nightly sleeper or just for guests/kiddos?

view full answer...

Answer 12

Hi Frank; the #RP74FR (68204) and #SWW-06 look different because they are a little different. The #RP74FR is only designed to work with the 68220 and 69220. If you have a different Sidewinder this wedge will not fit. It also fits a wider range of 5th…

view full answer...

How Much Does The Gen-Y Torsion 2-Ball Mount 325-GH-1225 Weigh?

Product Page this Question was Asked From

Continue Researching