Replacement Seals and Hardware for 3" Valterra Waste Valves

Question

Question:

Which seal or gasket do I need for the bayonet end of the valve where it connect to the camper sewer outlet?

asked by: Don E

0

Expert Reply:

Hey Don! The correct replacement for a 3" Valterra Waste valve like the item # T58 you were looking at is the Replacement Seals and Hardware for 3" Valterra Waste Valves item # T1003-7VP.

expert reply by: Jerred H

0

Don E.

12/3/2024

Jarred, These seals look like they are for the valve body, Not the bayonet connection. Am I mistaken?

Jerred H.

12/3/2024

@DonE Yes, that is correct. You need the Replacement Seal for Valterra 3" Caps and Hose Adapters item # T201 for a bayonet fitting.

Answer 1

Hi Joe, So you just need to know if the valve you are replacing slid over your pipe or into your pipe, and I'll go over how for you. If both ends of your waste valve slid into your sewer pipe you will need the Valterra Bladex Waste Valve for RV…

view full answer...

Answer 2

Go ahead and send me the pictures and I'll take a look to see which 1-1/2 inch Valterra seal you would need. The biggest visual difference is that the new Bladex Style part #T1001-9VP has a small lip on one corner of it that's used for…

view full answer...

Answer 3

With dually trucks I recommend the Swing Out Extension Brackets #LC182496 with the HappiJac Manual Truck Camper Jack System #LC736515-4. This is due to the Brophy Heavy Duty Cable Camper Jacks #CX74 having to sit under the lip of the camper. Since…

view full answer...

Answer 4

Hey Mike, we have a replacement seal for the Valterra 3 Hub to 3 Bayonet part #T1028 with the part #T201. Did you lose yours or did it get damaged?

view full answer...

Answer 5

Hi Sherry; the Replacement Seal for Valterra 3" Caps and Hose Adapters #T201 you were looking at is the correct seal for your #T05-2285VP.

view full answer...

Answer 6

It sounds like you are looking for the 3" Replacement Seal #T201. Do understand this is designed for Valterra 3" caps and adapters and while it may fit other manufacturers since they use similar designs it may not fit all. If you can tell…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Replacement Seals and Hardware for 3" Valterra Waste Valves

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching