Sealant to Use to Install Top Rail Trim part # 36279-955

Question

Question:

What is your recommendation for a sealant on this trim after installation. The top flat portion will be sealed with the roof, but I’m interested in what to use to seal the bottom edge and corners that will be on the side of the trailer contoured edge.

asked by: Tom H

0

Expert Reply:

Hey Tom, for a top rail like the part # 36279-955 I would recommend a non-sag sealant like the part # AL28KV. Non-sag means it can be applied to vertical surfaces and won't drip or run.

expert reply by: Jameson C

0

Jameson C.

12/15/2025

Hey Tom, how did the non-sag sealant work out on the bottom edge and corners of your trailer trim? Your results could really help others sealing similar contoured edges.

Answer 1

While I do not know if Freedom Trailers uses the Top Rail Trim for Enclosed Trailer #36279-955, I was able to get some measurements for you. The Top Rail Trim for Enclosed Trailer #36279-955 is 8' long, 2-3/4" wide and 1-1/2" deep. Each…

view full answer...

Answer 2

Hey Joe! The Top Rail Trim for Enclosed Trailer item #36279-955 measures 93-1/2" long and it is the longest length we have available. It's the longest size we carry of because of shipping. I do not know where you'll find a longer piece.…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 10

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 11

Hey Jesse, cool name! That's definitely a custom project, and there isn't a single off-the-shelf kit that'll give you everything you need. For a lift-up wall that's around 10' x 6', you're looking at building the door and…

view full answer...

Sealant to Use to Install Top Rail Trim part # 36279-955

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching