What Size Batteries and How Many Can Fit Inside the etrailer Trailer Tongue Tool Box e44VV?
Updated 12/15/2025 | Published 11/12/2024 >
Products Featured in This Question
Question:
What size batteries and how many can I fit in this tool box with room for other gear like chains, straps, blocks, etc?
asked by: John
Expert Reply:
Hey John! You would easily be able to install two standard size 12"-13" long x 6"-7" wide batteries like item # 34276285. This 12v 100 amp hour battery measures 12" long x 8-3/16" tall x 6-5/8" wide. A pair of these batteries could be lined up along the backside of the etrailer Trailer Tool Box item # e44VV leaving you quite a bit of available space for chains, blocks, and additional gear. You also have the option of using two larger batteries if you install them front to back instead of side by side along the back of the box. You could use two that measure up to 18" long and 9" wide each.
The etrailer Trailer Tongue Tool Box item # e44VV has a 6 cu ft capacity with internal measurements of 20-3/4" tall x 18-1/2" deep x 33-1/2" wide on the back side x 19-1/4" wide on the front side.
I have linked a diagram below so you can see the dimensions of this tool box.
Product Page this Question was Asked From
etrailer Trailer Tool Box - A-Frame - Aluminum - 6 Cu Ft - 34" Long - Matte Black
- Trailer Tool Box
- A-Frame Tool Box
- 19 - 22 Inch Tall
- Aluminum
- 31 - 40 Inch Long
- Black
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: LED Combination Trailer Tail Light - 6 Function - Submersible - 12 Diodes - Passenger Side
- Shop: etrailer Trailer Tool Box - A-Frame - Aluminum - 6 Cu Ft - 34" Long - Matte Black
- Video: A Closer Look at the etrailer A-Frame Trailer Tool Box
- Q&A: Vertical Spacing Between The Bottom Of The etrailer Trailer Tool Box And Gas Strut Mounting Bracket
- Q&A: Will a Generator Fit Inside the etrailer Trailer Tool Box e44VV?
- Shop: etrailer Electric Trailer Jack - Drop Leg - A-Frame - 18" Lift - 5,000 lbs
- Search Results: battery
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Search Results: trailer jack
- Shop: Suspension Enhancement
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Review of etrailer Trailer Tool Box - Matte Black Aluminum A Frame Trailer Tool Box - e64VV
- Shop: Brake Controller
- Q&A: What Sealant Should I Use Between an Aluminum Jeep-Style Fender and My Trailer?
- Search Results: trailer wiring
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Article: How to Measure for Trailer Hitch Drop
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Gooseneck Hitch
- Search Results: trailer lights



Jerred H.
12/15/2025
Hey John, how did your setup go with the two batteries in the etrailer tool box? Did you end up going with the side-by-side layout or the front-to-back fit? Your update could make it easier for others planning a similar setup.