Replacement Lever & Head Unit For 14k Equal-i-zer Weight Distribution Hitch

Question

Question:

I lost the pry bar for setting the swing arms in the bracket, how can I get another one?

asked by: Cory L

0

Expert Reply:

Hi Cory,

You can pick up the replacement snap-up lever right here for your Equal-i-zer Weight Distribution Hitch # EQ37140ET. For that, all you need is the following:

- Replacement Snap-Up Lever for Equal-i-zer Weight Distribution Systems # EQ95-01-6050

expert reply by: Kyle S

0

Cory

10/18/2024

Kyle, I had my mechanic look at it to adjust the hitch better for my trailer and he told me not to use it due to potential catastrophic failure of the welds where the ball mount top portion hooks up is cracked all around. Do you sell just that part (the riser is fine and i have the bars and mounts on the trailer)

Reply

Kyle S.

10/18/2024

@Cory Oh my, that sounds serious; glad you're taking action. And yes, we do have the replacement head unit for the 14,000 lb towing/1,400 lb tongue weight Equal-i-zer # EQ37140ET. What you need is the following: - Replacement Head for Equal-i-zer Weight Distribution Systems - 1,400 lbs TW # EQ90-02-1400 If you also want to/need to replace the hardware that attaches the shank to the head unit, you'll need the Replacement Bolts for Equal-i-zer Weight Distribution Head # EQ90-02-9100.

Reply

Cory

10/18/2024

@KyleS One last question as i am not sure if i have the 1200 or 1400 lb one (can’t find the label) do the bars fit the same for all of them so if i ordered the 1200 will my 1400 bars fit?

Reply

Kyle S.

10/18/2024

@Cory While not all Equal-i-zer heads are the same, the 1,400 lb bars do have the same size as the 1,200 lb bars so you can use the Replacement Head for Equal-i-zer Weight Distribution Systems - 1,200 lbs TW # EQ90-02-1200. You'll just want to make sure your trailer doesn't go over that capacity.

Reply

Answer 1

I'm not sure how to find out the age of your setup, but when I passed your photos along to my contact at Equal-i-zer he said that all you need to do for the upgraded system is swap out your 12K head unit for the 14K #EQ90-02-1400. Since your…

view full answer...

Answer 2

The Wet Equalizer Bolt with Locknut and Grease Zerk, #126B2, is a 9/16-18 inch bolt. The pitch, or threads per inch, is 18. This bolt comes with the matching locknut.

view full answer...

Answer 3

The Replacement Bolts for Equal-i-zer Weight Distribution Head part #EQ90-02-9100 contains four 3/4" flat washers that go on the bolt that attaches the head to the shank (see photo (#17)). If you instead need the washer that controls the head…

view full answer...

Answer 4

Hey Jim, for that weight trailer and your 2004 Ford F-250 I would recommend the Equal-i-zer kit part #EQ37140ET which has a tongue weight range of 1,100 lb to 1,400 lb and is widely considered the best WD and sway control around so this will work…

view full answer...

Answer 5

Hey Andrew! The Air Lift WirelessAIR Compressor System #AL58WQ you ordered is a great choice and one I often recommend. This comes with the EZ mount for a no drill installation and is dual path for side to side leveling. This will work well with the…

view full answer...

Answer 6

There area few differences between the 1,200 and 1,400 pound Equal-I-zer systems. The heads are different and the spring bars are different. If your tongue weight is over 1,200 pound then the 1,200 pound system is not rated high enough. When…

view full answer...

Answer 7

You are correct. You will only need the 14,000LB 2-5/16" Hitch Ball #EQ91-00-6140, Head #EQ90-02-1400 and Spring Bars #EQ90-01-1499 to convert your 10,000LB Hitch #EQ37100ET to a 14,000LB Hitch #EQ37140ET. The Sway Brackets #EQ95-01-5600 are…

view full answer...

Answer 8

With your tongue weight at 1,175 lbs when loaded, you also need to account for any cargo weight behind the rear axle as well to get the total tongue weight rating. I've attached an article to assist. You are correct that your current system is…

view full answer...

Answer 9

That's what we're here for Jim you're not bothering anybody. I found those parts you need for your Equal-i-zer Weight Distribution System item #EQ90-00-1000 and have listed them below: Replacement Snap-Up Lever for Equal-i-zer Weight…

view full answer...

Answer 10

I spoke my contact at Equal-i-zer and he told me that since it has 1 1/2" bars it is probably rated for 12,000 lbs. He said the way to tell for sure is to measure the bolt channel. If it measures 3/8" it is a 12,000 lb hitch, if it measures…

view full answer...

Answer 11

Yes, The Wiring and Safety Chain Extension Kit #PR34QR will work with your Hensley hitch per the manufacturer. This kit will help you if your chains and cables do not extend 24 inches past the end of the hitch box. The working load of the chains is…

view full answer...

Answer 12

The parts that are different between your 1,000 lb tongue weight rated Equal-i-zer kit part #EQ37100ET and the 1,600 lb tongue weight rated kit part #EQ64FR are just the spring bars and the head of the system. With that said the 1,600 lb tongue…

view full answer...

Replacement Lever & Head Unit For 14k Equal-i-zer Weight Distribution Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching