Width of Support Bar For Tongue Mounted Crossbar for Malone MicroSport Trailers

Question

Question:

How wide is the support bar at the base for the Tongue Mounted Crossbar for Malone MicroSport Trailers - 78 Long?

asked by: Tom T

0

Expert Reply:

Hi Tom,

The width is 1-1/4 inches for the bottom support bar of the Tongue Mounted Crossbar for Malone MicroSport Trailers # MPG4002.

expert reply by: Kyle S

0

Tom T.

9/21/2024

I asked the question incorrectly…how long is the support bar at the base for the Tongue Mounted Crossbar for Malone MicroSport Trailers - 78 Long

Kyle S.

9/23/2024

@TomT The base of the # MPG4002 is 45 inches long.

Answer 1

The Tongue Mounted Crossbar for Malone MicroSport Trailers #MPG4002 if pretty universal since it installs via a U-Bolt so I'm fairly confident it'll work just fine with your Yakima Rack n Roll trailer. This is designed for Malone MicroSport…

view full answer...

Answer 2

It doesn't look like there is an option to get the 13' Malone MicroSport Trailer #MPG460G and the Tongue Mounted Crossbar #MPG4002 with 58" long crossbars instead of the 78" long crossbars unfortunately. On the bright side this…

view full answer...

Answer 3

The distance from the top of the trailer tongue of the Microsport trailer to the top of the #MPG4002 measures 12 inches.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Hey Barry, yes the lowbed coversion kit part #MAL33TR and the retractable tongue kit part #MPG494 are both a fit for the Malone Microsport Trailer part #MPG460G. What are you planning on using the Microsport for?

view full answer...