Install Harness for Prodigy P3 Brake Controller in 2014 Ram 3500

Question

Question:

I bought the prodigy 3 brake controller for my ram3500 to pull a 5th wheel trailer and a motorcycle trailer on the back. do I need an adapter cable to make it work?

asked by: Robert E

0

Expert Reply:

Hey Robert, yes you would need the custom fit install harness part # 3023-P to make the install of your Prodigy P3 part # 90195 as easy as possible in your 2014 Ram 3500.

expert reply by: Jameson C

0

Bob

9/6/2024

Bought it, many thanks

Jameson C.

9/8/2024

@Bob Awesome!

Answer 1

There isn't anything like an autonomous controller that would step up if the factory controller fails. I'd simply bypass the existing factory brake controller. The GM ITBC, although it works better now than the earlier models has been…

view full answer...

Answer 2

I called my contact at Tekonsha and asked about replacing the Dodge Integrated Brake Controller if the truck is a 2010 through 2015. If you have a different year Ram just let me know and I can make some recommendations that will work for you. They…

view full answer...

Answer 3

Brake controller wiring harness #3023-P is indeed a fit for your 2013 Ram 1500. If you do not already have a brake controller I recommend the P2 #90885. This controller is easy to set up and use and it is reliable. I have linked a video showing the…

view full answer...

Answer 4

To install the #3023-P harness into your 2014 Ram 3500 you'll need to unplug the factory brake controller and use the same connector. Then the second 2-pin connector will normally be just above the brake pedal. If you check out the linked video…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Install Harness for Prodigy P3 Brake Controller in 2014 Ram 3500

Continue Researching