Valve Stem Hole Diameter that Internal Tire Sensor part # TM36FR is Designed to Fit

Question

Question:

What hole diameter on the wheel does the Internal Tire Sensor for TireMinder TPMS - 2-3/4inch Valve Stem, Part Number: TM36FR fit? 9.7mm, .453, or .625? I would be mounting on the inner dually on a 2023 Sprinter 3500XD Winnebago Navion. Thank you

asked by: Bill Y

0

Expert Reply:

Hey Bill, the Internal Tire Sensor part # TM36FR that you referenced is designed to fit the valve stem hole diameter of .625 inch.

expert reply by: Jameson C

0

Jameson C.

1/27/2026

Hey Bill, how did the .625-inch fit work out on your Sprinter’s inner dually wheel? Knowing how it mounted could help others setting up the same TireMinder sensor.

Answer 1

You sure can! You are looking for the TireMinder Internal Transmitter #TM36FR which will work with your TireMinder TMPS System. This transmitter has a battery with a 5-year life, and nickel plated finish to help it resist corrosion over time.

view full answer...

Answer 2

The Voyager monitor part #VOM719WP will work great as a replacement monitor for what you have now with the AOM-7694.

view full answer...

Answer 3

Yes, the Voyager Rear Camera with LED Low Light Assist part #VCMS17B will work perfectly with the Voyager Monitor AOM7694 and there will be no splicing required. I confirmed this with my contact at Voyager/Jensen for you. This does not have an up and…

view full answer...

Answer 4

Hello Fred, thanks for reaching out. The stem on the Internal Tire Sensor #TM36FR is rigid metal. I went out to our warehouse and looked at one. The stem does have a slight bend, but it is completely rigid and there would be no way you could bend it.…

view full answer...

Answer 5

Hey there Luis; good question as it's always smart to check, and I was able to verify that the TireMinder A1AS-6 system is 100% compatible with the internal sensors, which are the following part number: - Internal Tire Sensor for TireMinder TPMS…

view full answer...

Answer 6

TireMinder i10 TPMS for RVs and Trailers w/ Signal Booster #TM89FR can be used on rubber, steel, chrome, or nickel valve stems that are rated for more than 65psi. The lower pressure rubber valve stems aren't strong enough to handle the weight of…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 11

No long-term contract, Natalie - but a service plan is required to use the trackers. When you buy the 3000 with wifi assist #PM84FR, 5000 #PM64FR, or 5000 with wifi assist #PM74FR from etrailer, you’re purchasing the hardware/device only. To activate…

view full answer...

Answer 12

Hello Dustin, To mount the TecNiq Mini Side Marker Light - Amber - 3/4" - Grommet Mount - 9" Wire #TN22XR, you’ll need to drill a 3/4-inch diameter hole. The rubber grommet is designed to press-fit into this standard hole size, allowing the…

view full answer...

Valve Stem Hole Diameter that Internal Tire Sensor part # TM36FR is Designed to Fit

Continue Researching