Will Internal Tire Sensor for TireMinder TPMS Work With TireMinder A1AS-6

Question

Question:

Hello, Are these #TM36FR internal sensors compatible with the TireMinder A1AS-6 system? They will be used on a 2016 MB Sprinter 3500 RV.

asked by: Luis

0

Expert Reply:

Hey there Luis; good question as it's always smart to check, and I was able to verify that the TireMinder A1AS-6 system is 100% compatible with the internal sensors, which are the following part number:

- Internal Tire Sensor for TireMinder TPMS # TM36FR

expert reply by: Kyle S

0

Answer 1

Hey Gerald, great question, Yes, part #TM46FR is nickel plated, and that finish is there to help resist corrosion and wear over time so you’re not dealing with rust or extra upkeep. I know the photos can be a little confusing since it may look more…

view full answer...

Answer 2

Hey Robert, welcome back! The Internal Tire Sensor for TireMinder TPMS item #TM46FR is far better than an external tire pressure sensor. It's more accurate when it comes to PSI and temperature. The batteries last longer and you don't have to…

view full answer...

Answer 3

Hey Steve, welcome back. The Internal Tire Sensor for TireMinder TPMS item #TM46FR is compatible with the A1AS systems like item #TM49FR, i10 systems like item #TM56FR, TM-88C, and TM-77 systems. Please note that the Internal Tire Sensor for…

view full answer...

Answer 4

There are a couple of options to lift your trailer depending on if your axle's sit above or below the leaf springs. If you have torsion axles these systems won't work and I'll need to know what number axle you have to recommend the right…

view full answer...

Answer 5

Hello Fred, thanks for reaching out. The stem on the Internal Tire Sensor #TM36FR is rigid metal. I went out to our warehouse and looked at one. The stem does have a slight bend, but it is completely rigid and there would be no way you could bend it.…

view full answer...

Answer 6

Hey Bill, the Internal Tire Sensor part #TM36FR that you referenced is designed to fit the valve stem hole diameter of .625 inch.

view full answer...

Answer 7

Yes, you can use the TireMinder i10 TPMS for RVs and Trailers part #TM56FR on top of any factory TPMS sensors. It will simply screw on to the valve stem. The factory TPMS sensors will be inside the tire. The two will work together just fine, no…

view full answer...

Answer 8

I spoke with TireMinder and they assured me that the sensors from the A1A, part #TM-A1A-6, are compatible with the i10, part #TM89FR. Once you have paired the sensors to the i10, you will be able to monitor them the same as you would on the A1A.…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Will Internal Tire Sensor for TireMinder TPMS Work With TireMinder A1AS-6

Product Page this Question was Asked From

Continue Researching