Inner Diameter of Foot of Roadmaster Quick Foot Assembly Tongue Jack Extender RO84FR

Question

Question:

Can you tell me the inside diameter of this please? Thank you.

asked by: Mike B

0

Expert Reply:

Hey Mike, the Roadmaster Quick Foot Assembly Jack Extender part # RO84FR that you referenced was designed to fit 2 inch diameter inner jack legs. The inner diameter of the foot is right at 2-1/8 inches.

expert reply by: Jameson C

0

Answer 1

No, I am sorry there is no alternative to the Drop Leg for Lippert Power Jack - 8-11/16" Tall - 9" Diameter Footplate item #LC405217. The jack manufacturer's notch their tubes and have different diameters so they can't be used…

view full answer...

Answer 2

For your Bargman 84 series clearance light on your trailer we have the part #34-84-010 which is the correct replacement lens.

view full answer...

Answer 3

Since you have #34-84-700 backup lens, that indicates that you have a Bargman 84 series light, like #34-84-008. Any of the lens that you referenced, #34-84-010, #34-85-750, #47-84-712, will fit the Bargman 84 series light. It appears to me that the…

view full answer...

Answer 4

All three are very similar but there are differences between the three. Measure your stock trailer jack and buy the according jack that works for your application. Bulldog #BD1750290317 has clearance of 10-11/16 inches from mounting bracket to top of…

view full answer...

Answer 5

For a Bargman 84 series tail light we currently offer the Replacement Lens for Bargman Tail Light #34-84-711 and the Enhanced-Height Lens for Bargman #47-84-712. The #34-84-711 is 5-5/8" long x 4-1/4" wide x 7/8" deep and I've…

view full answer...

Answer 6

Hi Joshua; we have some compartment doors like the Valterra #A10-2150VP (white) or #A10-2150BKVP (black) you could install on the rear of your trailer. They measure 7-5/8" wide x 6-1/2" tall so that lines up with the size you need. They…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Inner Diameter of Foot of Roadmaster Quick Foot Assembly Tongue Jack Extender RO84FR

Product Page this Question was Asked From

Continue Researching