Replacement Parts for 18k Triple Axle Trailer
Updated 02/03/2026 | Published 07/18/2024
Products Featured in This Question
Question:
Parts Inquiry Application tri-axel trailer 18k 3tubes spindle- Inner bearing:1.375, Outer bearing: 1.25, grease seal: 1.93, thread width: 1. Require 2 sets of electric brakes mounting flanges for brakes 1 set of idler hubs 2 set of 8 or 6 lug drum hubs wheels Recommendations are welcome. Thanks!
asked by: Jeff F
Expert Reply:
Hi Jeff; assuming 3tubes meant 3" axle tubes/axle diameter you can use the Demco Trailer Brake Mounting Flange # DM52415 for 3" axles. However, if those bearing measurements are correct it indicates you have a # LM48548 inner bearing. We don't carry any hubs that use this bearing. I will also need to know the axle capacity to find the right brake assemblies.
The closest thing we have for a hub and drum is the # 8-407-5UC3-EZ which uses the # L68149 outer bearing with a 1.378" inner diameter and the # LM67048 inner bearing with a 1.25" ID. You might want to double check the outer bearing measurement with a digital caliper # PTW80157 to see if it matches. Then again, even if that is correct this uses a 10-19 grease seal and your measurement sounds like the # 10-40.
Are your axle tags still on the axle and readable? If you have the serial number and manufacturer name that will help find the rest of the parts needed. If you have some really old axles that could explain the bearing combination in which case replacement might be the only option.
Product Page this Question was Asked From
Easy Grease Trailer Hub and Drum Assembly for 5.2K - 7K Axles - 12" - 8 on 6.5 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Drum
- EZ Lube
- Pre-Greased
- 25580 / 14125A
- Standard Grade
- For 7000 lbs Axles
- 1/2 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- etrailer
more information >
Continue Researching
- Q&A: What Is The Difference Between 7K Hub/Drums From etrailer And Dexter?
- Q&A: Can A Load Range G Tire Be Installed On The Lionshead Aluminum Siberian Trailer Wheel LH78MR?
- Q&A: Looking for Preassembled and Greased Trailer Hub/Drum for Dexter 7,000 lb Trailer Axle
- Q&A: Looking for Front Jack Leg Replacement for Lippert Ground Control 3.0 of 2019 Highland Ridge MBH 371
- Q&A: What is Max Air Pressure for Lionshead Steel Modular Trailer Wheel LH44ZR
- Article: Trailer Wiring Diagrams
- Q&A: What Kind of Grease is Used in Your Pre-Greased Hubs? What Kind Can I Use?
- Q&A: Comparing Dexter and etrailer.com 7,000 Pound Electric Brake Assemblies
- Article: Electric Trailer Brakes: How They Work & What to Buy
- Article: Trailer Maintenance Schedule
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
Robin H.
2/3/2026
Hey Jeff, were you able to check your axle tags or confirm the bearing sizes with a digital caliper? Knowing what you found could help others trying to match older axle parts. Your update could make it easier for the next person working on a similar trailer setup.