50A Transfer Switch Needed for My RV

Question

Question:

Looking for a 50Amp transfer switch for my rv

asked by: Virgil M

0

Expert Reply:

Hey Virgil, thanks for reaching out!

Sounds like the Progressive Dynamics 50A Transfer Switch # PD52 is what you're looking for!

expert reply by: Jon G

0

Doc M.

11/23/2025

Hi Jon. I have a PD52 in my Dutchstarr. It took a crap. I purchased a PD52C witch has a generator sense @the base of the metal box. If I disconnect the 2 wires to it,would it work as a PD52?

Answer 1

Don't worry Gilles, even though your Progressive Dynamics PD52DCSD is obsolete you can replace it with the Transfer Switch #PD52. If you wish to still have the surge protection you can add the Power Watchdog #HU27FR in line of the transfer switch…

view full answer...

Answer 2

Hey Jimmy! Do you have 50 amp service on your RV? Assuming you do, the Progressive Dynamics 50A Transfer Switch - Metal Box - 120V/240V AC #PD52 is a good option and will work as a replacement.

view full answer...

Answer 3

I attached a section of the instructions which shows you should mount the Progressive Dynamics Transfer Switch - Metal Case - 50 Amp - 120V/240V #PD52 in the vertical position. It should not be installed in the horizontal position. If you need longer…

view full answer...

Answer 4

A transfer switch is installed to prevent power from being drawn from multiple sources (i.e. shore power, generator, inverter). The Go Power ATS #34264403 you were looking at is for transferring back and forth from inverter and shore power. Transfer…

view full answer...

Answer 5

I reached out to Progressive Dynamics to find out if you could have the shore power on the Normally Closed position for the Progressive Dynamics Transfer Switch #PD52, and this is what I was told via our tech contact: "I think there is confusion…

view full answer...

Answer 6

Hello Andrew. You are correct that the #PD52 cannot be mounted horizontally. An alternative would be to use the Furrion Automatic Transfer Switch #F50ATS. This is a very similar 50 amp transfer switch and it does not have any such mounting position…

view full answer...

Answer 7

The Progressive Dynamics Transfer Switch - Metal Case - 50 Amp - 120V/240V #PD52 (Alternatively PD52V) and the PD52DCS/PD52DCSV are both part of the PD52 series but there are some differences. Both share the same voltage rating and current ratings.…

view full answer...

Answer 8

A transfer switch is only going to have two receptacles to accept power from so you wouldn't be able to connect all of your systems together, but I do have a solution for you. You would need to use a 50 amp transfer switch like the Progressive…

view full answer...

Answer 9

I have a solution for you. As you know the unit you are looking for is no longer available and we do not have replacement parts either. However, I do have the replacement for that unit which is the following part: **Progressive Dynamics Transfer…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

50A Transfer Switch Needed for My RV

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching