Torque Spec on Lug Nuts for Aluminum Wildcat Trailer Wheel

Question

Question:

I just bought a 2024 Geo Pro 19FD and it has the Aluminum Wildcat Trailer Wheel - 15x6 Rim, 5 on 4-1/2, Item LH59VR - my question is what do I torque the nuts to? I cannot find anything that says what it is. I saw some YouTube video that said TT need to be torqued to 100 lbs. Is that a universal ? Thank you

asked by: Mark S

0

Expert Reply:

Hi Mark; we use the torque spec chart below for lug nuts on trailer wheels. Since the # LH59VR is a 15" aluminum wheel that fits 1/2"-20 wheel bolts the correct torque spec is 90-100 ft.-lbs.

expert reply by: Robin H

0

Lug Nut Torque Spec Chart
(click to enlarge)

Robin H.

2/17/2026

Hi Mark, how did things go torquing the lug nuts on your Geo Pro’s aluminum wheels? It’d be great to know if the 90–100 ft‑lb range worked well for you. Your update could make it easier for others checking their trailer wheels.

Answer 1

The high pressure alarm of your TPMS system should be set at 20-25% over your normal tire pressure and the low pressure alarm should be set at 10% below your normal tire pressure so that you can address the issue before it becomes a problem. For the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Torque Spec on Lug Nuts for Aluminum Wildcat Trailer Wheel

Continue Researching