Does The Length of the Yakima HD Crossbars Include The End Caps?

Question

Question:

The 60 Yakima HD roof racks, what is the total width of the rack with the end caps installed? I see it says rack length but Im needing 60 inches of usable rack inside the caps, is this the case? Or do I need to get the longer one?

asked by: Ken S

0

Expert Reply:

The 60" Yakima HD Crossbars # Y01157 are going to be 60" from end to end including the caps. As you need 60" of T-slot you would need to step up to the 68" Crossbars # Y01158.

expert reply by: Bud M

0

Katrina D.

2/17/2026

Hey, did the 68-inch Yakima HD crossbars give you the full usable width you needed? Knowing how that fit worked out could really help others trying to size their racks correctly.

Answer 1

Hello Justin, The channel nut is 35mm long x 19mm wide x 8mm tall in the Pioneer Platform Mounting Kit for Rhino-Rack Heavy-Duty Crossbars #RR43105.

view full answer...

Answer 2

Hey Chip, yes I agree the metal lid of the Ventline Ventadome part #V2110SP-24 is going to hold up the best over time which would mean you wouldn't have to worry about replacing the lid for a very long time. How old is the trailer?

view full answer...

Answer 3

In order to determine the correct replacement lid for your 1996 Dutchman Thor, you are going to need to measure your actual vent. The most common size vents are 14-1/4" x 14-1/4" so you'll want to verify that yours is a standard vent.…

view full answer...

Answer 4

Most likely we have what you are looking for but you will need to first determine what vent you have on your trailer. In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly…

view full answer...

Answer 5

If your old vent cover was held on by a pin, we have some replacement vent lids that would work great for you. For white, use part #CAM40154 or for smoke colored, use #CAM40147.

view full answer...

Answer 6

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 7

Yes, the TrackTowers part #Y52AV does fit into Yakima HD tracks like what you have installed on your trailer.

view full answer...

Answer 8

Yes, the TrackTowers for Yakima Crossbars and Platforms #Y52AV that you referenced do fit the Rhino-Rack RTC-Style Roof Rack Tracks #RTC18.

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

The Yakima HD Crossbars #Y01159 have a 3/8" opening on the top of the bar which is 1/4" tall and 13/16" wide inside the slot opening. This will accept both the Replacement T-Bolt with Nut for Yakima Rack and Roll Trailers #Y8880184 and…

view full answer...

Answer 11

We can get what you need depending on exactly what you're doing the Thule Xadapt12 part #THXADAPT12 could work. It uses barrel nuts that thread down on the bolts for security. You can use the Replacement M8 T-Bolt part #853-0782 this will allow…

view full answer...

Answer 12

The thickness of the T-bolt head of the part #Y8880184 you referenced is 5/32 of an inch. I attached a picture that has all of the other dimensions as well. These T-bolts are M10 x 1.5 x 25

view full answer...

Does The Length of the Yakima HD Crossbars Include The End Caps?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching