How Much Does The Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers 325-GH-524 Weigh?

Question

Question:

How much does this weigh?

asked by: Ross T

0

Expert Reply:

Hello Ross. The Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers # 325-GH-524 weighs 37.8 lbs all together.

expert reply by: Jesse M

0

Ross T.

6/10/2024

Thanks so much for both replies! Have a great day. Ross

Answer 1

Yes, you need what is called a pulse preventer, #5501. You mentioned that you have an older Ford truck. Depending on how old it is you may need to connect the brake controller red wire to a different location on the truck. If your truck is a 1989 to…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Kenny, welcome back! The reason for that note is because all of the new systems since 2025 use R32 refrigerant due to EPA regulations. Any 2024 and older systems use R410A and their parts are not compatible with the R32 units. It doesn't mean…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

How Much Does The Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers 325-GH-524 Weigh?

Product Page this Question was Asked From

Continue Researching