Replacement Crank Handle For a RAM 20K Square Trailer Jack

Question

Question:

TJDDP-20000SP-F What is the part for the jack handle for this Ram jack?

asked by: Mark C

0

Expert Reply:

It sounds like you are wanting the Replacement Sidewind Crank # TJD-12000-HD for the Jack # TJDDP-20000SP-F. While our product page says the handle is for the 12K jack it is the same handle used on the RAM 12K, 15K, 20K and 25K jacks.

expert reply by: Bud M

0

Answer 1

I have an option for you, but the Replacement Handle for Buyers Products Heavy Duty Square Jacks #3370091405H is the correct replacement handle for Buyers Products jacks 3370091410H and 3370091415H. We have the Replacement Sidewind Crank for etrailer…

view full answer...

Answer 2

I reached out to my contact at Ram and he mentioned that based on the description of your jack you either have the #TJD-12000TW-R with no return spring on the lower leg, or the #TJD-12000TWSP-F which has the return spring on the lower leg. Both of…

view full answer...

Answer 3

I went out to our warehouse and measured the end of the Sidewind Crank, #TJD-12000-HD. The inside width of the opening measured 1-1/2 inches. The outside measured 1-7/8 inches and the tangs measured 1-3/4 of an inch. In case you want to know, the…

view full answer...

Answer 4

Here is a list of the replacement parts we have for the Ram 12K Support Capacity Jack #TJD-12000SP-F2 you found. Replacement Sidewind Crank #TJD-12000-HD Replacement Plunger Pin Assembly #TJD-12000-PPN Replacement Cap #TJD-12000-CP Replacement Return…

view full answer...

Answer 5

We spoke with our contacts at RAM jacks and they informed us that the length of the #TJD-12000-HD is 14-1/2 inches and the radius is 13 inches.

view full answer...

Answer 6

To get your Diamond C dump trailer back in working condition you'll need to swap out the entire jack as that internal drive screw isn't available as a replacement. For a replacement jack I recommend going with our etrailer Trailer Jack…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Crank Handle For a RAM 20K Square Trailer Jack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching