Replacement Hub and Seal for 2005 Shorelandr PWC Trailer

Question

Question:

Good morning! Looking for some product guidance. I have a 2005 ShoreLandr 1200/1400 single place PWC trailer. Im looking to replace the hubs, bearings, seals, wheels, and tires. What I need help with is identifying the proper seal. I have the prior seals but am unable to identify any part numbers on them for a cross reference. The original hub is a DICO 45263 with inner/outer bearings L44649. Can you help me identify the appropriate seal? Would the seal that comes in this kit be the proper ID for this application? My plan is to use the following parts: Hub: AKIHUB-545-2-G-EZ-2K Wheel/Tire: AM31202 Seal: TBD Thanks! Matt

asked by: Matt D

0

Expert Reply:

Hey Matt, based on the bearings you mentioned the correct grease seal would be the # 10-9.

The trailer hub part # AKIHUB-545-2-G-EZ-2K is correct for your axle and it comes with the correct seal already.

This is compatible with the wheel and tire part # AM31202 as well.

expert reply by: Jameson C

0

Answer 1

Based on previous information we have received I see the DICO 45263 uses the Grease Seal #168255TB, inner/outer Bearing #L44649 and inner/outer Race #L44610. If you want a whole new assembly you would need the Hub #AKIHUB-545-2-G-EZ-2K but you would…

view full answer...

Answer 2

We've had customers with your Dico 45263 hub in the past get us their bearing numbers so we know that for a replacement with the wheel bolt pattern you need you could use the #AKIHUB-545-2-G-EZ-2K and you'd be set.

view full answer...

Answer 3

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 4

There's no reason you couldn't use a 7-way junction box like the part #38656 to install a 4-way. It would be just a matter of wiring up only 4 posts of the junction box on the input and output side of the box instead of 4. With only 4-wires…

view full answer...

Answer 5

Grease seals such as those included with the #DBRKHW35EZ bearing kit should be be installed so that they are flush with the hub bore. If the correct seal is used, everything should fit together perfectly. As long as the castle nut is correctly ran…

view full answer...

Answer 6

We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Hub and Seal for 2005 Shorelandr PWC Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching