Total Extended Height of the etrailer Ram Square Trailer Jack

Question

Question:

Hello - can you tell me the dimension from the bottom of the foot to the bottom of the mounting bracket with the jack and leg fully extended?

asked by: Dave

0

Expert Reply:

Hi Dave, the total extended length of the etrailer Boat Trailer Jack w/ Footplate # MJSQ-2500B is 22 5/8". Retracted it measures 7 1/4" for a total lift of 29 1/8".

expert reply by: Bryce D

0

Jack Dimensions
(click to enlarge)

Answer 1

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 2

Without the drop leg extended the Square Jack w/ Footplate part #MJSQ-2500B lift is 15-3/8". The total lift is 29-1/8" with the drop leg extended.

view full answer...

Answer 3

Fulton Square Drop Leg for Stabilizer Jack, 29" Long Item #FSJ20324 by itself will be 24-3/4 inches tall from where it attaches to the jack to the bottom of the foot with the drop leg in the tallest position. It is essentially more than doubling…

view full answer...

Answer 4

We don't offer a caster wheel for the etrailer #MJSQ-2500B 2500 lb capacity jack you mentioned, mainly because the casters will limit the capacity of the jack because the capacity of the caster wheels typically top out at 1000-1200 lbs.…

view full answer...

Answer 5

In regards to the Square Jack with Footplate part #MJSQ-2500B, the overall dimensions of the jack are 24-3/4" tall while retracted or 40-1/8" tall while extended x 2-1/4" wide at the body. I have attached some other common dimensions…

view full answer...

Answer 6

Having a deck height for a trailer of 13-14 inches is pretty low. Using the 4 inch drop Timbren setup part #A35RD545E would give you the best chance of it getting that low. The center of the spindle will end up being 1/4 of an inch below the trailer…

view full answer...

Answer 7

The drop spindle model you mentioned, part #A35RD545E would be used over the straight spindle model, part #A35RS545E if you wanted a lower deck height on your car trailer. Since you are most likely already using ramps, I cannot see how you would…

view full answer...

Answer 8

It sounds like you're looking for a 3,500 lb axle measuring 80-5/8" long with a 4" drop. I do have a solution, but we do not have an axle that matches this length. What I can offer is the Timbren Axle-Less Trailer Suspension System.…

view full answer...

Answer 9

The base on 2-Speed Boat Trailer Winch #315-W2500D measures 5-3/4 inches wide by 7-1/8 inches long. I have included a picture showing this for you and a link to a video review on this winch.

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Total Extended Height of the etrailer Ram Square Trailer Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching