Distance From Bottom of Shank to Lowest Point on Fastway Solid Steel and B&W Tow & Stow 2-Ball Mount
Updated 05/02/2024 | Published 05/01/2024
Products Featured in This Question
Question:
I am trying to determine the dimension shown by the Red line in the attached photo. That is, distance between bottom edge of Shank where it enters the receiver, and lowest point of shank that points to the ground. My problem is that due to a very severe dip at the bottom of my driveway, the clearance between the bottom of the hitch and the ground is pretty tight, when going through that dip, even though I have plenty of clearance on level ground. I cannot seem to find drawings anywhere that help. The 2 hitches that I am most interested in, are the Fastway Adjustable Steel HD 49-00-5625, and the BandW Stow and Go TS20037B. Both options are for a 2.5 inch receiver. Any other suggestions would be appreciated.
asked by: TomR
Expert Reply:
The measurement you're looking for on the Flash Strong Solid Steel 2-Ball Mount # FA49-00-5625 is 6-3/4" and on the B&W Tow & Stow 2-Ball Mount # BWTS20037B it is 5-1/2". You're going to have more clearance on the B&W but that is also due to the fact that it has less of a drop at 5" vs. 7" from the Fastway.
If the B&W meets your needs then that would be the way to go. I also recommend using the # 34061775-D to keep it secure. I don't have a way to tell if this would clear on your drive or not without testing it but I'd say this is about as good as it gets for an adjustable ball mount. You could continue to gain clearance by reducing the rise/drop but it would lose it's value for towing.
(click to enlarge)
Product Page this Question was Asked From
Flash Strong Solid Steel 2-Ball Mount - 2-1/2" Hitch - 6" Drop, 7" Rise - 20K
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- Two Balls
- 2 Inch Ball
- 2-5/16 Inch Ball
- Steel Shank
- Drop - 6 Inch
- Rise - 7 Inch
- Fits 2-1/2 Inch Hitch
- 20000 lbs GTW
- Fastway
more information >
Continue Researching
- Shop: Shocker Hitch HD Air Cushioned 2-Ball Mount - 2-1/2" Hitch - 4-1/2" Drop - 20K
- Shop: Gen-Y Phantom X Adjustable 2-Ball Mount - 2-1/2" Hitch - 16K - 5" Drop
- Search Results: trailer hitch ball mount
- Q&A: Recommended Adjustable Ball Mount w/ 2-5/16 and 2 Balls for a 2-1/2 Hitch
- Q&A: How Tall Is The B&W Tow & Stow 2-Ball Mount # BWTS20040B To Maintain The Recommended 11" Clearance?
- Shop: Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch, 4" Drop/5" Rise, 18.5K, Aluminum
- Shop: InfiniteRule Hitch Locks for B & W Tow and Stow 10K and 14.5K Ball Mounts - Qty 4
- Shop: Gen-Y Torsion 2-Ball Mount - 2-1/2" Hitch - 2-1/2" Rise/5" Drop - 16K
- Shop: Shocker Hitch HD Ball Mount - 2-5/16" Ball - 2-1/2" Hitch - 2" Rise/Drop -20K
- Shop: Shocker Hitch HD Air Ball Mount - 2-5/16" Ball - 2-1/2" Hitch - 8-1/2" Drop - 20K
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Search Results: trailer wiring
- Q&A: Does Truck with 6-1/2 ft bed Have to Use Slider Hitch for Turning Clearance with Fifth Wheel Hitch
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Shop: Suspension Enhancement
- Shop: Brake Controller
- Q&A: Availability of Heat Strip or Heat Pump for Furrion Chill Cube RV AC
- Video: B&W Companion OEM 5th Wheel Hitch Manufacturer Breakdown
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Gooseneck Hitch
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
on Drop Hitch
