Is 1/4 Inch Height Difference Okay For Use With E-Z Flex Equalizers
Updated 05/06/2024 | Published 04/30/2024 >
Products Featured in This Question
Question:
I have a Bubbas 18foot ATV trailer with double axles. Not sure of the axle size, but its pretty beefy. The horizontal spacing on the shackle holes center to center on the equalizers is 7 3/4, but the vertical spacing between the shackle hole and the equalizer mounting hole is around 2 3/4inch center to center. I notice the K71-655-00 has the 7 3/4inch horizontal spacing, but it shows the vertical spacing as 3 inches. Is that close enough to what I have or will it not line up right being a 1/4inch different? Sam
asked by: Sam
Expert Reply:
Hi Sam,
Good question, and the mere 1/4 inch difference in the height is not going to have any type of negative effect on your trailer so you can 100 percent use the E-Z Flex Equalizers # K71-655-00.
These are a smart choice as they'll make a nice difference in how your trailer rides due to its rubber cores absorbing bounce and shock.
Product Page this Question was Asked From
- Trailer Suspension Parts
- Shackle Links
- Camper
- Car Hauler
- Utility Trailer
- 3-1/2 Inch Long
- TruRyde
more information >
Continue Researching
- Shop: MORryde Shock Absorbing Suspension Equalizers for Tandem Axle Trailers w/ 35" Wheelbase - 8K
- Shop: Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Tandem Axle - 8,000 lbs
- Search Results: trailer suspension parts
- Video: E-Z Flex Equalizers Review
- Q&A: Choosing the Right Dexter E-Z Flex Suspension for Replacing Standard Equalizers
- Q&A: Equalizer Upgrade Recommendation For 7-3/4 Inch Long Equalizer on Tandem Axle Trailer
- Shop: E-Z Flex Equalizers - Double-Eye Springs - Tandem Axle - 8,000 lbs - Qty 2
- Shop: DeeMaxx Disc Brake Kit w/ Actuator for Tandem Axle Trailers - 13" Hub/Rotor - 8 on 6-1/2 - 7K
- Shop: Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Tandem Axle - 6,000 lbs
- Shop: Dexter Bronze Bushings - Qty 4
- Shop: Replacement Wet Shoulder Bolt - Equa-Flex Tandem Axle Suspension - 9/16" x 3-3/8" - Qty 1
- Q&A: Are Different Sizes For The E-Z Lube Grease Cap Plug Available?
- Search Results: equalizers
- Q&A: What Is The Purpose Of The Progressive Dynamics Charge Wizard Pendant
- Q&A: Wire Gauge for Progressive Dynamics 9300 Series RV Converter Charger
- Search Results: battery charger
- Search Results: rv electrical
- Video: Review of Progressive Dynamics RV Power Converter - Standard Charge - PD89RR
- Search Results: deemax
- Search Results: grease cap
- Search Results: lippert dust cap
- Q&A: Idler Hubs and DeeMax Slip On Disc Brake Kit for 2019 Big Country 3360ss
- Q&A: How To Measure To Make Sure The MORryde CRE3000 Equalizers Will Fit Your Trailer
- Video: Dexter E-Z Flex Suspension Kit Spec Review
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: Parts Needed to Add Hydraulic Disc Brakes to a Trailer
- Video: All You Need to Know About the DeeMaxx Disc Brakes
- Video: The Low-Down on the DeeMaxx Disc Brake Kit w/ Actuator for Tandem Axle Trailers
- Video: Titan Hydraulic Brake Lines and Fittings Review


Sam
5/4/2024
So I have all the measurements on my trailer now, just want to make sure I get the correct equalizer and shackle combination. Axle spacing is 33 1/2" Outer shackle bolt holes 7 3/4" Hanger bolt hole to shackle bolt hole is 3 7/8" Side bolt hole to hanger hole is 2 3/4" Shackle strap length is 3 1/4 So I'm a little concerned that the shackle length difference will not line up right on my trailer. Any further insight? Thanks. Sam