Install Instructions/Manual for Redarc Tow Pro Liberty Brake Controller

Question

Question:

I have a redarkRed24fr controller I bought 2-3 years ago and need a new installation guide. How do I get a replacement?

asked by: Mike C

1

Helpful Expert Reply:

Hey Mike, I attached install instructions for the Redarc Tow Pro Liberty part # RED24FR to this page for you to check out.

expert reply by: Jameson C

1

Answer 1

Hello Frank, thanks for reaching out. Sounds like typical Ford for you lol. We do have a plug-in brake controller option for the 2025 Ford F-250. For that I recommend the Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness #RED67CR since it…

view full answer...

Answer 2

For your 12V wiring to your 7-way, we have people running many different things off that 12V wire. 12 gauge or even better 10 gauge ensures that the power is transferred timely and accurately. We have a kit for brake controllers and 12V wiring for…

view full answer...

Answer 3

I was able to locate the correct bearings, races and seal that correspond to the part numbers you provided in your question. For bearings you will need the part #L44649 and for races you will want #L44610. Then for the grease seal you will use part…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

Since everything else is working on your Redarc Tow-Pro Liberty Brake Controller #RED24FR there may be a problem with the light pipe on the control knob. there is a 90 degree light pipe which is what brings the light up and out through the button. If…

view full answer...

Answer 6

I sure can help you out with installing the P2 brake controller #90885 in your 2007 Chevy Avalanche. The brake controller white wire will go to the truck white wire for ground Controller black wire goes to truck red/black wire for power in Dark blue…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Install Instructions/Manual for Redarc Tow Pro Liberty Brake Controller

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching