Do You Carry Both The Keyed and Non-Keyed Versions Of The Lippert Slam Latch?

Question

Question:

Lippert Slam Latch for RV Doors - Black Item LC54PJ Do you also have a non-keyed version of this? I need both keyed and non-keyed. - Thanks!

asked by: Bill C

0

Expert Reply:

We only carry the Keyed # LC54PJ version of the Lippert Slam Latch.

expert reply by: Bud M

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 8

Hey Jeff! The MORryde GooseTech 5th Wheel to Gooseneck Pin Box #MR97MV comes with a Demco eZ-Latch. The best option for a lock is the InfiniteRule Lock for Cast Demco eZ-Latch Trailer Couplers #IR66FR. This is designed to for a standard coupler but…

view full answer...

Answer 9

Hey there Trace! There are parts of the steel brackets that come into contact with the aluminum bed on your new 2026 F350 Super Duty (congrats on the new truck by the way - those are super nice!). B&W says to use strips of polypropylene tape…

view full answer...

Answer 10

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 11

Welcome back John! I'm going to need a bit more information to confirm the MORryde GooseTech item #MR57MV is the correct one. I checked with the manufacturer and your 2024 Dutchman Astorian 230ML 5th wheel trailer comes standard with a Curt…

view full answer...

Answer 12

Hey Travis! The right MORryde GooseTech depends on the pin box bolt pattern and GVWR of the Solitude 310GK. If it is a little older it probably has a Lippert 1621, I believe the newer models use the Lippert Rhino. You can ask whoever you're…

view full answer...

Do You Carry Both The Keyed and Non-Keyed Versions Of The Lippert Slam Latch?

Product Page this Question was Asked From

Continue Researching