Replacement Trunnion Arms for 4,500 lb Fastway e2 Weight Distribution

Question

Question:

I have a Fastway e2 trunnion WDH. It’s a 4500lb and I’d like to get sway bar brackets. I see only for 6K and up. Is there a similar product for the lighter WDH? Thanks

asked by: Francois C

0

Expert Reply:

Hey Francois!

The replacement arms you're looking for can be found as part # FA58FR on our site. These are rated for the 4,500 lb system and it comes with both arms.

Let me know if you need anything else so we can get you back up and towing!

expert reply by: Jon G

0

Answer 1

The Fastway e2 Weight Distribution w/ 2-Point Sway Control - Trunnion - 4,500 lbs GTW, 450 lbs TW #FA92-00-0450 weighs 55-lbs; the head itself is the heaviest single piece at 19-lbs.

view full answer...

Answer 2

Hi Justin! The SumoSprings Solo Custom Helper Springs - Rear Axle #SS68DR would be a very good option for your 2023 Toyota 4Runner. They will provide up to 1,400 pounds of support (at 50% compression) and I think that would be plenty for your…

view full answer...

Answer 3

Hi Andy! The Timbren bump stops #T85MR and #T25MR will indeed fit your 2025 Ford Maverick LARIAT Hybrid AWD. However, The #T25MR is rated up to 8,600 pounds, so it will likely be way to stiff and be very jarring when you hit them. The 4,800 pound…

view full answer...

Answer 4

Hi Brian; although there are Air Lift 1000 Air Helper Springs #AL42WQ for the 2024 Ford Maverick they are not a fit for the Tremor models. The only option for suspension enhancement on your Tremor is the Timbren SES #T25MR. These will give you the…

view full answer...

Answer 5

We have 2 sets of Timbren Jounce springs for your 2022 Ford Maverick. The 8,600LB Springs #T25MR and the 4,800LB Springs #T85MR. The 4,800lb springs are their off-road bump stops and will provide you more suspension travel than the standard 8,600lb…

view full answer...

Answer 6

It will; what is happening is the tongue weight is creating the "V" you mentioned, so you are not towing level, and a weight distribution system is exactly what you need. This will level you out, and for your 330 lb loaded tongue weight,…

view full answer...

Answer 7

To install Timbrens on your FWD 2022 Ford Maverick you'll have to go with the Timbren Active Off-Road Bumpstops #T85MR as the Kit #T25MR you're looking at isn't designed to fit your truck. Timbren markets the Off-Road bumpstops as being…

view full answer...

Answer 8

Hi Mike; we do have the 92-02-0444 which is the same as the #FA98FR. This will replace the trunnion knuckle on the #FA92-00-0450.

view full answer...

Answer 9

We do offer the following stainless steel hitch balls that include stainless steel washers and nuts. 1-7/8" Ball #63851 2" Ball #F37CR 2-5/16" Ball #63853

view full answer...

Answer 10

I went out to the warehouse and pulled Pins and Thumb Clips #EQ95-01-9415 to measure them for you. The diameter is 3/8 of an inch. The usable length is just under 2-1/2 inches (2.45 inches). And the opening is 2.46 inches by 1.5 inches.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Trunnion Arms for 4,500 lb Fastway e2 Weight Distribution

Product Page this Question was Asked From

Continue Researching