Could etrailer Replacement Rod and Nut TJD-12000-RODNUT Fit 2016 Big Tex

Question

Question:

Will this work for my bigtex 2016 14et ..trailer jack failed n3ed to replace inners

asked by: Joel G

0

Expert Reply:

Hey Joel, check the brand of the landing gear on your 2016 Big Tex and see if you can find a brand. If you see the Ram jack brand or even possibly the etrailer brand and if so the part # TJD-12000-RODNUT would be the correct replacement part.

If you see a different brand let me know and I'll see what you may need.

expert reply by: Jameson C

0

Answer 1

The bearing is not included with the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K part #TJD-12000-RODNUT. There is a bearing washer at the top but the bearing is sold separately as the Replacement Bearing for etrailer…

view full answer...

Answer 2

Pacific Rim is the manufacturer of the RAM jacks. You can verify the Replacement Rod and Nut #TJD-12000-RODNUT you found is the correct part by confirming your jack is 3-1/2" by 3-1/2" square and the 1" rod is 17-3/4" long. If you…

view full answer...

Answer 3

We do not have this item in stock for me to measure its thread pitch but two of us estimated it as being 6 or 7 threads per inch. I linked a photo of the instructions to replace this part. The bearing is removable and is available as a replacement…

view full answer...

Answer 4

The Ram Trailer Jacks generally use a 1" diameter threaded rod whereas the Bulldog Trailer Jacks generally use a 1-1/4" threaded rod. Therefore, it would appear as if you have a Bulldog Trailer Jack and in which case the Replacement Screw…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Could etrailer Replacement Rod and Nut TJD-12000-RODNUT Fit 2016 Big Tex

Product Page this Question was Asked From

Continue Researching