Tow Bar Lighting Solution for 1990 Jeep Wrangler
Updated 04/02/2024 | Published 04/01/2024
Products Featured in This Question
Question:
Good afternoon. Im just getting ready to add your beefed up front and rear anti sway bars and front and rear SumoSprings to my 2011 30ft. Itasca Cambria Ford E-450 that Jameson has been helping me with. I want to flat tow my 90 stock 1991 YJ Wrangler Standard Transmission behind the RV and this tow bar looks perfect and the write-ups are encouraging. Now.....heres the question....I would like the tail-lights and turn signal lights on the Wrangler to function in unison with the RV. Which wiring kit do you recommend. The RV is pre-wired with the 6 pin round receptacle co-located just beside the 2inch square receiver. Thanks. David H
asked by: David H
Expert Reply:
Hey David, for your 1990 Jeep Wrangler the Roadmaster Diode Kit part # RM-15267 would be a really great option. This installs diodes on the Wrangler's taillight circuits which allows the RV to control them. It also comes with the wiring that runs to the trailer wiring at the rear of your RV. You did mention that you have a 6-pin but most likely what you have is the standard 7-way which also has a center pin that gets counted. You also mentioned 90 and 1991 so I am not totally sure what year Wrangler you have but this kit fits both.
Product Page this Question was Asked From
Curt Adjustable Tow Bar - Coupler Style for 2" Ball - 5,000 lbs
- Tow Bar
- Coupler Mount
- Fixed - Binding
- Steel
- 5000 lbs
- Stores Separately
- Cables Not Included
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Rear Sway Bar and SumoSpring Kit for 2011 Itasca Cambria to Improve Handling
- Shop: Curt Adjustable Tow Bar - Coupler Style for 2" Ball - 5,000 lbs
- Video: Complete Breakdown of the Curt Adjustable Tow Bar
- Shop: Suspension Enhancement
- Search Results: steering stabilizer
- Shop: SumoSprings Solo Custom Helper Springs - Rear Axle
- Shop: Vehicle Tow Bar Wiring
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord
- Search Results: tow bars
- Search Results: ssf~111~54
- Shop: Roadmaster Rear Anti-Sway Bar - 1-1/2" Diameter
- Video: What to Know About the SumoSprings Solo Custom Helper Springs
- Shop: SumoSprings Solo Custom Helper Springs - Front Axle
- Shop: Hopkins Custom Tail Light Wiring Kit for Towed Vehicles
- Shop: Redarc 12V Smart Battery Monitor - 500 Amp
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Q&A: Trailer Wiring Installation on 1999 Ford E450 Van
- Q&A: Adapters Needed For A Reese Tow Bar To Demco Base Plate On A 2001 Jeep Cherokee
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Flat Towing Package for 2012-2014 Honda CR-V
- Q&A: Troubleshooting a 2017 Chevy Equinox Wobbling While Being Flat Towed
- Article: Best Vehicles to Flat Tow Behind an RV
- Article: Must-Have Flat Towing Components
- Q&A: Parts Needed For Flat Towing a 2000 Ford Ranger Behind a Motorhome/RV
- Q&A: Will the Blue Ox Base Plate Adapter Kit # BX8833 Fit a U-Haul Tow Bar
- Article: Roadmaster Vehicle Specific Base Plates
- Article: What Is a Supplemental Braking System?
- Article: The Definitive, Step-by-Step Flat Towing Setup Guide
David H.
4/1/2024
Yep...It's a 1991 YJ with that nice size straight 6 - 4.0 L. engine. standard manual trans with "shiftable" manual 4-wheel drive. It probably weighs 2,500 lbs and since I can put the transmission in neutral and I can also put the 4-wheel drive in neutral it should be no problem to flat tow with no issues....and weighing only a couple thousand pounds not extra braking mechanics should be needed. Once again....Thanks for all you help ! David H.