Availability of Replacement Key for Pop & Lock Custom Tailgate Lock

Question

Question:

Hi there I bought a car and I believe it had a pop and lock installed on the tail gate. I was just wondering if I can get a copy of the key or do I have to go through a locksmith. Thanks and I hope to hear from you soon.

asked by: Lee

0

Expert Reply:

You can get a replacement key for your # PAL6100 through Pop & Lock if you give them the number stamped into the face of the lock cylinder. If you can't get this for some reason the only option would be to get the replacement lock cylinder through them and have a locksmith open it to swap them out. While you're at it, you might want to consider adding the Pop & Lock Power Upgrade Kit # PL8630.

expert reply by: Robin H

0

Lee

3/29/2024

Ok thanks for the information. How much is the replacement key if I can provide you the number stamp on the outside cylinder?

Robin H.

4/1/2024

@Lee you will have to send that information directly to Pop & Lock and ask them about the price.

Lee

4/2/2024

@RobinH thank you

Answer 1

If the BAKFlip G2 Hard Tonneau Cover #BAK26601 was installed on your 2014 Honda Ridgeline and it was folded back you would have no interference with it and your trunk. If the G2 cover was folded down the door would open basically as tall as the…

view full answer...

Answer 2

The BAKFlip F1 Hard Tonneau Cover #BAK72601, which is a fit for your 2012 Honda Ridgeline, will be installed in the same manner as you see in the attached demonstration video. I also attached a link to the instructions which are somewhat universal…

view full answer...

Answer 3

The BAKBox 2 Truck Bed Toolbox part #BAK92601 measures 10" wide so it should not interfere with the trunk lid but you want to measure the clearance between the open trunk lid and the cab to be sure. However, the BAKBox 2 attaches to BAKFlip…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Availability of Replacement Key for Pop & Lock Custom Tailgate Lock

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching